|
BQ29311_15 Datasheet, PDF (3/24 Pages) Texas Instruments – FOUR-CELL LITHIUM-ION | |||
|
◁ |
www.ti.com
Not Recommended for New Designs
bq29311
SLUS487D â DECEMBER 2001 â REVISED NOVEMBER 2003
ELECTRICAL CHARACTERISTICS
TA = 25°C, CREG = 1 µF, VCC = 14 V (unless otherwise noted)
SUPPLY CURRENT
PARAMETER
TEST CONDITIONS
I(CC1) Supply current 1
I(CC2) Supply current 2
No load at VREG, TOUT,
LEDOUT, XALERT, SCLK,
SDATA. CLKIN not used
VBAT ⤠VSD, VPACK = 0
DSG, CHG and PCHG = off
TA = 25°C
TA = â 25°C to 85°C
TA = â 25°C to 85°C
MIN TYP MAX UNIT
140 190
µA
220
1 µA
3.3 V REGULATOR
PARAMETER
V(REG)
Regulator output voltage
âV(REGTEMP)
Regulator output change with
temperature
âV(REGLINE) Line regulation
âV(REGLOAD) Load regulation
TEST CONDITIONS
IO ⤠25 mA,
V(SD) = 6.5 V ⤠VCC ⤠25 V,
IO = 25 mA
TA = â 25°C to 85°C
TA = â25°C to 25°C
TA = 25°C to 85°C
V(SD) =6.5 V ⤠VCC ⤠25V,
0.1 mA ⤠IO ⤠25 mA,
IO = 25 mA
VCC = 14 V
SHUTDOWN VI MONITOR
PARAMETER
V(SD)
VREG shutdown threshold range(1)
âV(SD)
Shutdown threshold steps
Vhys(SD) Hysteresis
Accuracy of the shutdown threshold
TEST CONDITIONS
Measured at VBAT
Set by SDV register b0 âb3
(1) V(SD) = V(REG) brownout threshold voltage as determined by b0 âb3 in the SDV register.
BROWNOUT VIN MONITOR
PARAMETER
VBO
Brownout threshold range(1)
âVBO
Brownout threshold steps
Vhys(BO) Hysteresis
Brownout threshold accuracy
TEST CONDITIONS
Measured at VBAT
Set by SDV register b4 â b7
(1) VBO = V(REG) brownout threshold voltage as determined by b4 âb7 in the SDV register.
CELL VOLTAGE MONITOR
PARAMETER
TEST CONDITIONS
V(CELL_OUT) VCELL output (see Note 4)
V(CELL_IN) Differential Input voltage range
V(CELL_IN) = 0 V
V(CELL_IN) = 4.5 V
VC1 to VC2, VC2 to VC3,
VC3 to VC4, VC4 to VC5
K
R(BAL)
VCELL scale factor
Cell balance internal resistance
[0.975 âV(CELL_OUT) ]/V(CELL_IN)
RDS(ON) for internal FET switch at V(DS) = 2 V
(1) The V(CELL) output is inversely proportional to the V(CELL_OUT) = âK Ã V(CELL_IN) + 0.975.
MIN
3.135
TYP MAX
3.3 3.465
± 0.2% ± 1.74%
± 0.2% ± 1.74%
6
20
2
20
UNIT
V
mV
mV
MIN
6.475
35
TYP MAX
10.975
300
50
65
± 5%
UNIT
V
mV
mV
MIN
7.975
35
TYP MAX
12.475
300
50
65
± 5%
UNIT
V
mV
MIN TYP
0.975
0.3
MAX
UNIT
V
0
4.5 V
0.144 0.150 0.156
500
â¦
3
|
▷ |