TS3A5223_14 Datasheet, PDF (2/15 Pages) Texas Instruments – 0.45Ω Dual SPDT Bidirectional Analog Switch

TS3A5223
SCDS339A – JANUARY 2013 – REVISED FEBRUARY 2013
NAME
VCC
NC1, NO1, NC2,
NO2
COM1, COM2
GND
SEL1, SEL2
PIN NUMBER
1
5, 2, 7, 10
TS3A5223 PIN DESCRIPTION
DESCRIPTION
Postive supply Input – Connect 1.65V up to 3.6V supply
Channel Input/Output signal Pins
3, 9
Channel Input/Output signal Pins
6
Ground reference pin
4, 8
Select logic pin
www.ti.com
T_A
–40°C to 85°C
PART NUMBER
TS3A5223RSWR
ORDERING INFORMATION⁽¹⁾
PACKAGE
10-Pin µ-QFN
Reel of 3000
TOP-SIDE MARKING
B2_
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
ABSOLUTE MAXIMUM RATINGS⁽¹⁾
Specified at T_A= –40°C to 85°C unless otherwise noted.
VCC
V_IN-Max
I_OUT-Max
I_OUT-Peak
P_D
ESD
Positive DC Supply Voltage
Pins S1A, S1B, S2A, S2B, OUT1, OUT2, SEL1, SEL2 to GND pin voltage
Pin OUT1, OUT2 max DC current
Pin OUT1, OUT2 peak current (1ms pulse at 10% duty cycle)
Total device power dissipation
at T_A = 85°C
ESD Rating – HBM
10-µQFN RSW
ESD Rating – CDM
VALUE
MIN
–0.3
–0.3
MAX
4.3 ⁽²⁾
4.3 ⁽²⁾
±300
±500
UNIT
V
V
mA
mA
430 mW
2000 V
500 V
T_A
Operating free-air ambient temperature range
T_J
Junction temperature range
T_stg
Storage temperature range
–40
85 °C
–55
150 °C
–55
150 °C
(1) Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these conditions is not implied. Exposure to absolute-maximum-rated conditions for
extended periods may affect device reliability.
(2) Not rated for continuous operation, 0.5% duty cycle at 1 kHz recommended
DISSIPATION RATINGS^(1)(2)(3)
BOARD
High-K
PACKAGE
10-Pin µ-QFN
θ_JC
46°C/W
θ_JA ⁽³⁾
93°C/W
DERATING
FACTOR ABOVE
T_A = 25ºC
10.7 mW/ºC
T_A < 25°C
1075W
T_A = 70°C
590mW
T_A = 85°C
430mW
(1) Maximum dissipation values for retaining device junction temperature of 150°C
(2) Refer to TI’s design support web page at www.ti.com/thermal for improving device thermal performance
(3) Operating at the absolute T_J-max of 150°C can affect reliability– for higher reliability it is recommended to ensure T_J < 125°C
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range (unless otherwise noted)
VCC
V_Max
T_A
dt/dv
Positive DC Supply Voltage
Pins NC1, NO1, NC2, NO2, COM1, COM2, SEL1, SEL2 to GND pin maximum voltage
Operating free-air ambient temperature range
SEL pin Input rise and fall ^{VCC= 1.6 to 2.7V}
time limit
VCC = 3.0 to 3.6V
MIN MAX UNIT
1.65 3.6 V
0 3.6 V
–40
85 ºC
sec/V
2
Submit Documentation Feedback
Product Folder Links :TS3A5223
Copyright © 2013, Texas Instruments Incorporated