SN74LVTH273-EP Datasheet, PDF (2/9 Pages) Texas Instruments – 3.3-V ABT OCTAL D-TYPE FLIP-FLOP WITH CLEAR

SN74LVTH273ĆEP
3.3ĆV ABT OCTAL DĆTYPE FLIPĆFLOP
WITH CLEAR
SCBS769A − NOVEMBER 2003 − REVISED JUNE 2006
FUNCTION TABLE
(each flip-flop)
INPUTS
CLR CLK D
OUTPUT
Q
L
X
X
L
H
↑
H
H
H
↑
L
L
H H or L X
Q0
logic diagram (positive logic)
11
CLK
1D
2D
3
4
CLK(I)
1D
C1
R
1D
C1
R
3D
7
1D
C1
R
4D
8
1D
C1
R
5D
13
1D
C1
R
6D
14
1D
C1
R
7D
17
1D
C1
R
8D
18
1D
C1
R
1
CLR
R
2
5
6
9
12
15
16
19
1Q
2Q
3Q
4Q
5Q
6Q
7Q
8Q
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)^†
Supply voltage range, V_CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.6 V
Input voltage range, V_I (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
Voltage range applied to any output in the power-off state, V_O (see Note 1) . . . . . . . . . . . . . . . . −0.5 V to 7 V
Voltage range applied to any output in the high state, V_O (see Note 1) . . . . . . . . . . . . . −0.5 V to V_CC + 0.5 V
Current into any output in the low state, I_O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA
Current into any output in the high state, I_O (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 mA
Input clamp current, I_IK (V_I < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
Output clamp current, I_OK (V_O < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
Package thermal impedance, θ_JA (see Note 3): NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94.4°C/W
PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83°C/W
Storage temperature range, T_stg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† _{Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and}
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
2. This current flows only when the output is in the high state and VO > VCC.
3. The package thermal impedance is calculated in accordance with JESD 51-7.
4. Long-term high-temperature storage and/or extended use at maximum recommended operating conditions may result in a reduction
of overall device life. See http://www.ti.com/ep_quality for additional information on enhanced plastic packaging.
2
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265