74ACT11533 Datasheet, PDF (2/7 Pages) Texas Instruments – OCTAL D-TYPE TRANSPARENT LATCHES WITH 3-STATE OUTPUTS

54ACT11533, 74ACT11533
OCTAL DĆTYPE TRANSPARENT LATCHES
WITH 3ĆSTATE OUTPUTS
SCAS017A − D2957, JULY 1987 − REVISED APRIL 1993
logic symbol^†
24
OC
EN
13
C
C1
23
1D
1D
22
2D
21
3D
20
4D
17
5D
16
6D
15
7D
14
8D
1
1Q
2
2Q
3
3Q
4
4Q
9
5Q
10
6Q
11
7Q
12
8Q
† _{This symbol is in accordance with ANSI/IEEE Std 91-1984}
and IEC Publication 617-12.
logic diagram (positive logic)
24
OC
13
C
23
1D
C1
1D
22
2D
C1
1D
21
3D
C1
1D
20
4D
C1
1D
17
5D
C1
1D
ą
1
1Q
2
2Q
3
3Q
4
4Q
9
5Q
16
6D
C1
1D
10
6Q
15
7D
C1
1D
11
7Q
Pin numbers shown are for the DW, JT, and NT packages.
14
8D
C1
1D
12
8Q
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)^‡
Supply voltage range, V_CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 6 V
Input voltage range, V_I (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to V_CC + 0.5 V
Output voltage range, V_O (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to V_CC + 0.5 V
Input clamp current, I_IK (V_I < 0 or V_I > V_CC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 20 mA
Output clamp current, I_OK (V_O < 0 or V_O > V_CC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 50 mA
Continuous output current, I_O (V_O = 0 to V_CC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 50 mA
Continuous current through V_CC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 200 mA
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
‡ _{Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only and}
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
2−2
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265