SN74V245-EP Datasheet, PDF (1/42 Pages) Texas Instruments – DSP-SYNC FIRST-IN, FIRST-OUT MEMORY

SN74V245-EP
www.ti.com
SCAS932A – DECEMBER 2012 – REVISED JANUARY 2013
4096 × 18 DSP-SYNC™ FIRST-IN, FIRST-OUT MEMORY
Check for Samples: SN74V245-EP
FEATURES
1
•2 4096 × 18-Bit Organization Array
• 7.5-ns Read and Write Cycle Time
• 3.3-V VCC, 5-V Input Tolerant
• First-Word or Standard Fall-Through Timing
• Single or Double Register-Buffered Empty and
Full Flags
• Easily Expandable in Depth and Width
• Asynchronous or Coincident Read and Write
Clocks
• Asynchronous or Synchronous Programmable
Almost-Empty and Almost-Full Flags With
Default Settings
• Half-Full Flag Capability
• Output Enable Puts Output Data Bus in High-
Impedance State
• High-Performance Submicron CMOS
Technology
• DSP and Microprocessor Interface Control
Logic
• Provide a DSP Glueless Interface to Texas
Instruments TMS320™ DSPs
• Packaged in 64-Pin Thin Quad Flat Package
SUPPORTS DEFENSE, AEROSPACE,
AND MEDICAL APPLICATIONS
• Controlled Baseline
• One Assembly and Test Site
• One Fabrication Site
• Available in Military (–55°C to 125°C)
Temperature Range
• Extended Product Life Cycle
• Extended Product-Change Notification
• Product Traceability
DESCRIPTION/ORDERING INFORMATION
The SN74V245 is a very high-speed, low-power CMOS clocked first-in first-out (FIFO) memory. It supports clock
frequencies up to 133 MHz and has read-access times as fast as 5 ns. This DSP-Sync FIFO memory features
read and write controls for use in applications such as DSP-to-processor communication, DSP-to-analog front
end (AFE) buffering, network, video, and data communications.
The SN74V245 is a synchronous FIFO, which means each port employs a synchronous interface. All data
transfers through a port are gated to the low-to-high transition of a continuous (free-running) port clock by enable
signals. The continuous clocks for each port are independent of one another and can be asynchronous or
coincident. The enables for each port are arranged to provide a simple interface between DSPs,
microprocessors, and/or buses controlled by a synchronous interface. An output-enable (OE) input controls the
3-state output.
The synchronous FIFO has two fixed flags, empty flag/output ready (EF/OR) and full flag/input ready (FF/IR), and
two programmable flags, almost-empty (PAE) and almost-full (PAF). The offset loading of the programmable
flags is controlled by a simple state machine, and is initiated by asserting the load pin (LD). A half-full flag (HF) is
available when the FIFO is used in a single-device configuration.
Two timing modes of operation are possible with the SN74V245: first-word fall-through (FWFT) mode and
standard mode.
In FWFT mode, the first word written to an empty FIFO is clocked directly to the data output lines after three
transitions of the RCLK signal. A read enable (REN) does not have to be asserted for accessing the first word.
In standard mode, the first word written to an empty FIFO does not appear on the data output lines unless a
specific read operation is performed. A read operation, which consists of activating REN and enabling a rising
RCLK edge, shifts the word from internal memory to the data output lines.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
DSP-SYNC, TMS320 are trademarks of Texas Instruments.
2
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2012–2013, Texas Instruments Incorporated