ISO3086T_15 Datasheet, PDF (1/31 Pages) Texas Instruments – Isolated 5-V RS-485 Transceiver With Integrated Transformer Driver

Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
Reference
Design
ISO3086T
SLLSE27D – JANUARY 2011 – REVISED OCTOBER 2015
ISO3086T Isolated 5-V RS-485 Transceiver With Integrated Transformer Driver
1 Features
•1 Meets or Exceeds TIA/EIA-485-A
• Signaling Rate up to 20 Mbps
• 1/8 Unit Load – Up to 256 Nodes on a Bus
• Thermal Shutdown Protection
• Typical Efficiency > 60% (I_LOAD = 100 mA) - see
SLUU469
• Low Bus Capacitance 7 pF (Typ)
• 50-kV/µs Typical Transient Immunity
• Fail-safe Receiver for Bus Open, Short, Idle
• Logic Inputs are 5-V Tolerant
• Bus-Pin ESD Protection
– 11-kV HBM Between Bus-Pins and GND2
– 6-kV HBM Between Bus-Pins and GND1
• Safety and Regulatory Approvals
– 4242 V_PK Basic Insulation per DIN V VDE V
0884-10 and DIN EN 61010-1
– 2500 V_RMS Isolation for 1 minute per UL 1577
– CSA Component Acceptance Notice 5A, IEC
60950-1 and IEC 61010-1 Standards
2 Applications
• Isolated RS-485/RS-422 Interfaces
• Factory Automation
• Motor/Motion Control
• HVAC and Building Automation Networks
• Networked Security Stations
3 Description
The ISO3086T is an isolated differential line
transceiver with integrated oscillator outputs that
provide the primary voltage for an isolation
transformer. The device is a full-duplex differential
line transceiver for RS-485 and RS-422 applications
that can easily be configured for half-duplex operation
by connecting pin 11 to pin 14, and pin 12 to pin 13.
These devices are ideal for long transmission lines
since the ground loop is broken to allow for a much
larger common-mode voltage range. The symmetrical
isolation barrier of the device is tested to provide
4242 V_PK of isolation for 1 minute per VDE between
the bus-line transceiver and the logic-level interface.
Any cabled I/O can be subjected to electrical noise
transients from various sources. These noise
transients can cause damage to the transceiver
and/or near-by sensitive circuitry if they are of
sufficient magnitude and duration. These isolated
devices can significantly increase protection and
reduce the risk of damage to expensive control
circuits.
The ISO3086T is specified for use from –40°C to
85°C.
Device Information⁽¹⁾
PART NUMBER
PACKAGE
BODY SIZE (NOM)
ISO3086T
SOIC (16)
10.30 mm × 7.50 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Control
Circuitry
Typical Application Circuit
X-FMR
4
8
D1
3
2
C1
1
7
6
5
D2
C4 C5
1 _D1
2
D2
16
V_CC2
C3
4 _VCC1
C2
3
GND1
14
A
13
B
5
12
R
Z
6
RE
11
Y
7
15
DE
8D
9, 10
GND2
ISO3086T
LDO
1 _IN
5
OUT
3 _EN
C6
2 _{GND NC} 1
Isolated Supply to
other Components
RS-485 Bus
Interface
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.