TIBPAL16L8-7C Datasheet, PDF (9/23 Pages) Texas Instruments – HIGH-PERFORMANCE IMPACT-X E PAL CIRCUITS

TIBPAL16L8-7C, TIBPAL16R4-7C, TIBPAL16R6-7C, TIBPAL16R8-7C
HIGH-PERFORMANCE IMPACT-X ™ PAL^® CIRCUITS
SRPS006D – D3115, MAY 1988 – REVISED MARCH 1992
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage, V_CC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Voltage applied to disabled output (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 75°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
NOTE 1: These ratings apply except for programming pins during a programming cycle.
recommended operating conditions
MIN NOM MAX UNIT
VCC
VIH
Supply voltage
High-level input voltage (see Note 2)
4.75
5 5.25 V
2
5.5 V
VIL
IOH
IOL
fclock
tw
Low-level input voltage (see Note 2)
High-level output current
Low-level output current
Clock frequency
Pulse duration, clock (see Note 2)
High
Low
0.8 V
– 3.2 mA
24 mA
0
100 MHz
5
ns
5
tsu
Setup time, input or feedback before clock↑
th
Hold time, input or feedback after clock↑
TA
Operating free-air temperature
7
ns
0
ns
0
25
75 °C
NOTE 2: These are absolute voltage levels with respect to the ground pin of the device and include all overshoots due to system and/or tester
noise. Testing these parameters should not be attempted without suitable equipment.
electrical characteristics over recommended operating free-air temperature range
PARAMETER
TEST CONDITIONS
MIN TYP^† MAX UNIT
VIK
VCC = 4.75 V,
II = – 18 mA
–0.8 – 1.5 V
VOH
VCC = 4.75 V,
IOH = – 3.2 mA
2.4 3.2
V
VOL
IOZH‡
IOZL‡
VCC = 4.75 V,
VCC = 5.25 V,
VCC = 5.25 V,
IOL = 24 mA
VO = 2.7 V
VO = 0.4 V
0.3 0.5 V
100 µA
–100 µA
II
IIH‡
IIL‡
IOS§
VCC = 5.25 V,
VCC = 5.25 V,
VCC = 5.25 V,
VCC = 5.25 V,
VI = 5.5 V
VI = 2.7 V
VI = 0.4 V
VO = 0.5 V
100 µA
25 µA
–80 –250 µA
– 30 –70 –130 mA
ICC
VCC = 5.25 V,
VI = 0,
Outputs open
160 180 mA
Ci
f = 1 MHz,
VI = 2 V
5
pF
Co
f = 1 MHz,
VO = 2 V
6
pF
Cclk
f = 1 MHz,
VCLK = 2 V
6
pF
† _{All typical values are at VCC = 5 V, TA = 25°C.}
‡ _{I/O leakage is the worst case of IOZL and IIL or IOZH and IIH respectively.}
§ _{Not more than one output should be shorted at a time, and the duration of the short circuit should not exceed one second. VO is set at 0.5 V to}
avoid test problems caused by test equipment ground degradation.
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265
9