TL071_10 Datasheet, PDF (7/40 Pages) Texas Instruments – LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS

electrical characteristics, V_CC± = ±15 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS^†
T_A‡
TL071C
TL072C
TL074C
TL071AC
TL072AC
TL074AC
TL071BC
TL072BC
TL074BC
TL071I
TL072I
TL074I
UNIT
MIN TYP MAX MIN TYP MAX MIN TYP MAX MIN TYP MAX
25°C
V_IO
Input offset voltage V_O = 0,
R_S = 50 Ω _{Full range}
3 10
13
3
6
7.5
2
3
5
3
6
mV
8
Temperature
α
VIO
coefficient of input V_O = 0,
R_S = 50 Ω Full range
18
18
18
18
μV/°C
offset voltage
I_IO
Input offset current V_O = 0
25°C
Full range
5 100
10
5 100
2
5 100
2
5 100 pA
2 nA
I_IB
Input bias current^§ V_O = 0
25°C
Full range
65 200
7
65 200
7
65 200
7
65 200 pA
20 nA
V_ICR
V_OM
A_VD
Common-mode
input voltage range
Maximum peak
output voltage
swing
Large-signal
differential voltage
amplification
R_L = 10 kΩ
R_L ≥ 10 kΩ
R_L ≥ 2 kΩ
V_O = ±10 V, R_L ≥ 2 kΩ
25°C
25°C
Full range
25°C
Full range
−12
±11
to
15
±12 ±13.5
±12
±10
25 200
15
−12
±11
to
15
±12 ±13.5
±12
±10
50 200
25
−12
±11
to
15
±12 ±13.5
±12
±10
50 200
25
−12
±11
to
15
±12 ±13.5
±12
±10
50 200
25
V
V
V/mV
B₁
Unity-gain
bandwidth
25°C
3
3
3
3
MHz
r_i
CMRR
k_SVR
I_CC
Input resistance
Common-mode
rejection ratio
Supply-voltage
rejection ratio
(ΔV_{CC ±} /ΔV_IO)
Supply current
(each amplifier)
V_IC = V_ICRmin,
V_O = 0,
R_S = 50 Ω
V_CC = ± 9 V to ±15 V,
V_O = 0,
R_S = 50 Ω
V_O = 0,
No load
25°C
25°C
25°C
25°C
10¹²
70 100
70 100
10¹²
75 100
80 100
10¹²
75 100
80 100
10¹²
Ω
75 100
dB
80 100
dB
1.4 2.5
1.4 2.5
1.4 2.5
1.4 2.5 mA
V_O1/ V_O2
Crosstalk
attenuation
A_VD = 100
25°C
120
120
120
120
dB
† _{All characteristics are measured under open-loop conditions with zero common-mode voltage, unless otherwise specified.}
‡ _{Full range is TA = 0°C to 70°C for TL07_C,TL07_AC, TL07_BC and is TA = −40°C to 85°C for TL07_I.}
§ _{Input bias currents of an FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive, as shown in Figure 4. Pulse techniques must be used}
that maintain the junction temperature as close to the ambient temperature as possible.