TS3V340_10 Datasheet, PDF (6/26 Pages) Texas Instruments – QUAD SPDT HIGH-BANDWIDTH VIDEO SWITCH WITH LOW AND FLAT ON-STATE RESISTANCE

TS3V340
QUAD SPDT HIGHĆBANDWIDTH VIDEO SWITCH
WITH LOW AND FLAT ONĆSTATE RESISTANCE
SCDS172A - JULY 2004 − REVISED DECEMBER 2004
electrical characteristics over recommended
V_CC = 3.3 V + 0.3 V (unless otherwise noted)^†
PARAMETER
TEST CONDITIONS
operating
free-air temperature range,
MIN TYP‡ MAX UNIT
VIK
IIH
IIL
IOZ§
IOS¶
Ioff
ICC
∆ICC
ICCD
CIN
COFF
EN, IN
EN, IN
EN, IN
EN, IN
EN, IN
D port
S port
VCC = 3 V,
VCC = 3.6 V,
VCC = 3.6 V,
VCC = 3.6 V,
VCC = 3.6 V,
VCC = 0,
VCC = 3.6 V,
VCC = 3.6 V,
VCC = 3.6 V,
D and S ports open,
VIN or VEN = 5.5 V,
IIN = −18 mA
VIN and VEN = 5.5 V
VIN and VEN = GND
VO = 0 to 5.5 V,
VI = 0,
Switch OFF
VO = 0.5 VCC,
VI = 0,
Switch ON
VO = 0 to 5.5 V,
VI = 0
II/O = 0,
Switch ON or OFF
One input at 3 V,
Other inputs at VCC or GND
VEN = GND,
VIN input switching 50% duty cycle
3.3 V or 0,
f = 1 MHz
VI = 5.5 V, 3.3 V, or 0, f = 1 MHz,
Outputs open,
Switch OFF
−1.8 V
±1 µA
±1 µA
±1 µA
50
mA
1 µA
0.7 1.5 mA
30 µA
0.35
mA/
MHz
2.5 3.5 pF
5.5
7
pF
3.5
5
CON
VI = 5.5 V, 3.3 V, or 0, f = 1 MHz,
Outputs open,
Switch ON
10.5
14 pF
ron#
VCC = 3 V
VI = 1 V,
VI = 2 V,
IO = 13 mA
IO = 26 mA
3
6
Ω
3
6
ron(flat)||
VCC = 3.3 V,
VI = 0 to VCC,
IO = 26 mA
1
Ω
† _{VI, VO, II, and IO refer to I/O pins.}
‡ _{All typical values are at VCC = 3.3 V (unless otherwise noted), TA = 25°C.}
§ _{For I/O ports, the parameter IOZ includes the input leakage current.}
¶ _{The IOS test is applicable to only one ON channel at a time. The duration of this test is less than 1 s.}
# _{Measured by the voltage drop between the D and S terminals at the indicated current through the switch. ON-state resistance is determined by}
the lower of the voltages of the two (D or S) terminals.
|| _{ron(flat) is the difference of ron in a given channel at specified voltages.}
switching characteristics over recommended operating free-air temperature range,
V_CC = 3.3 V + 0.3 V, R_L = 75 Ω, C_L = 20 pF (unless otherwise noted) (see Figures 6 and 7)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
MIN TYP MAX UNIT
tpd(s)
IN
D
tON
IN or EN
S
tOFF
IN or EN
S
2
5 ns
4
7 ns
2
7 ns
dynamic characteristics over recommended operating free-air
V_CC = 3.3 V + 0.3 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
DG^k
DP^k
RL = 150 Ω,
RL = 150 Ω,
f = 3.58 MHz,
f = 3.58 MHz,
See Figure 7
See Figure 7
BW
RL = 150 Ω,
See Figure 8
XTALK
RL = 150 Ω,
f = 10 MHz,
RIN = 10 Ω,
OIRR
RL = 150 Ω,
f = 10 MHz,
See Figure 10
‡
k
All typical values are at VCC
DG and DP are expressed in
= 3.3 V (unless otherwise
absolute magnitude.
noted),
TA
=
25°C.
See Figure 9
temperature range,
TYP‡
0.2
0.1
500
−80
−60
UNIT
%
°
MHz
dB
dB
6
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265