|
TS3V330_10 Datasheet, PDF (6/26 Pages) Texas Instruments – QUAD SPDT WIDE-BANDWIDTH VIDEO SWITCH WITH LOW ON-STATE RESISTANCE | |||
|
◁ |
TS3V330
QUAD SPDT WIDE-BANDWIDTH VIDEO SWITCH
WITH LOW ON-STATE RESISTANCE
SCDS162C â MAY 2004 â REVISED JULY 2005
www.ti.com
Electrical Characteristics
over recommended operating free-air temperature range, VCC = 3.3 V ± 0.3 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS(1)
MIN TYP(2) MAX
VIK
Vhys
IIH
IIL
IOZ (3)
IOS (4)
Ioff
ICC
âICC
ICCD
CIN
COFF
EN, IN
EN, IN
EN, IN
EN, IN
EN, IN
EN, IN
D port
S port
VCC = 3 V,
IIN = â18 mA
VCC = 3.6 V,
VIN and VEN = VCC
VCC = 3.6 V,
VIN and VEN = GND
VCC = 3.6 V,
VO = 0 to 3.6 V,
VCC = 3.6 V,
VO = 0.5 VCC,
VCC = 0 V,
VO = 0 to 3.6 V,
VCC = 3.6 V,
II/O = 0,
VCC = 3.6 V,
One input at 3.4 V,
VCC = 3.6 V,
VEN = GND
VIN input switching 50% duty cycle
VIN of VEN = 0,
f = 1 MHz
VI = 0,
Switch OFF
VI = 0,
Switch ON
VI = 0
Switch ON or OFF
Other inputs at VCC or GND
D and S ports open,
VI = 0,
f = 1 MHz,
Outputs open, Switch OFF
â1.8
150
±1
±1
±1
50
15
10
750
0.45
3.5
10
5
CON
ron (5)
VI = 0,
VCC = 3 V
f = 1 MHz,
VI = 1 V,
VI = 2 V,
Outputs open,
IO = 13 mA,
IO = 26 mA,
Switch ON
RL = 75 â¦
RL = 75 â¦
17
5
7
7 10
UNIT
V
mV
µA
µA
µA
mA
µA
µA
µA
mA/
MHz
pF
pF
pF
â¦
(1) VI, VO, II, and IO refer to I/O pins.
(2) All typical values are at VCC = 5 V (unless otherwise noted), TA = 25°C.
(3) For I/O ports, IOZ includes the input leakage current.
(4) The IOS test is applicable to only one ON channel at a time. The duration of this test is less than one second.
(5) Measured by the voltage drop between the D and S terminals at the indicated current through the switch. ON-state resistance is
determined by the lower of the voltages of the two (D or S) terminals.
Switching Characteristics
over recommended operating free-air temperature range, VCC = 3.3 V ± 0.3 V, RL = 75 â¦, CL = 20 pF (unless otherwise
noted) (see Figure 5)
PARAMETER
tON
tOFF
FROM
(INPUT)
S
S
TO
(OUTPUT)
D
D
MIN TYP MAX UNIT
2.5 6.5 ns
1.1 3.5 ns
Dynamic Characteristics
over recommended operating free-air temperature range, VCC = 3.3 V ± 0.3 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
DG (2)
DP (2)
BW
XTALK
OIRR
RL = 150 â¦,
RL = 150 â¦,
RL = 150 â¦,
RL = 150 â¦,
RL = 150 â¦,
f = 3.58 MHz,
f = 3.58 MHz,
See Figure 7
f = 10 MHz,
f = 10 MHz,
See Figure 6
See Figure 6
RIN = 10 â¦, See Figure 8
See Figure 9
(1) All typical values are at VCC = 5 V (unless otherwise noted), TA = 25°C.
(2) DG and DP are expressed in absolute magnitude.
TYP (1)
0.82
0.1
300
â80
â50
UNIT
%
Deg
MHz
dB
dB
6
|
▷ |