TL103W_08 Datasheet, PDF (5/12 Pages) Texas Instruments – DUAL OPERATIONAL AMPLIFIERS WITH INTERNAL REFERENCE

www.ti.com
TL103W, TL103WA
DUAL OPERATIONAL AMPLIFIERS
WITH INTERNAL REFERENCE
SLOS437J – APRIL 2004 – REVISED JULY 2005
OPAMP2, Independent Operational Amplifier
Electrical Characteristics
V_CC+ = 5 V, V_CC = GND, V_O = 1.4 V, T_A = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
V_IO
αV_IO
I_IO
Input offset voltage
TL103W
TL103WA
Input offset voltage drift
V_icm = 0 V
V_icm = 0 V
Input offset current
I_IB
A_VD
k_SVR
V_ICR
Input bias current
Large-signal voltage gain
Supply-voltage rejection ratio
V_CC+ = 15 V, R_L = 2 kΩ,
V_O = 1.4 V to 11.4 V
V_CC+ = 5 V to 30 V
Input common-mode voltage range V_CC+ = 30 V⁽¹⁾
CMRR
I_source
I_SC
Common-mode rejection ratio
Output source current
Short circuit to GND
I_sink
Output sink current
V_OH
High-level output voltage
V_CC+ = 15 V, V_O = 2 V, V_id = 1 V
V_CC+ = 15 V
V_CC+ = 15 V, V_O = 2 V,
V_id = –1 V
V_CC+ = 15 V, V_O = 0.2 V,
V_id = –1 V
V_CC = 30 V, R_L = 2 kΩ
V_CC = 30 V, R_L = 10 kΩ
V_OL
Low-level output voltage
SR
Slew rate at unity gain
GBW Gain bandwidth product
THD
V_n
Total harmonic distortion
Equivalent input noise voltage
R_L = 10 kΩ
V_CC+ = 15 V, C_L = 100 pF,
R_L = 2 kΩ, V_I = 0.5 V to 3 V,
unity gain
V_CC+ = 30 V, V_I = 10 mV,
C_L = 100 pF, R_L = 2 kΩ,
f = 100 kHz
V_CC+ = 30 V, V_O = 2 V_pp,
C_L = 100 pF, R_L = 2 kΩ,
f = 1 kHz, A_V = 20 dB
V_CC = 30 V, R_S = 100 Ω,
f = 1 kHz
T_A
25°C
Full range
25°C
Full range
25°C
25°C
Full range
25°C
Full range
25°C
Full range
25°C
25°C
Full range
25°C
Full range
25°C
25°C
25°C
25°C
Full range
25°C
Full range
25°C
Full range
25°C
MIN TYP
MAX UNIT
1
4
5
mV
0.5
3
5
7
µV/°C
2
75
nA
150
20
150
nA
200
50 100
25
V/mV
65 100
dB
0
V_CC+ – 1.5
V
0
V_CC+ – 2
70
85
dB
60
20
40
mA
40
60 mA
10
12
mA
12
50
26
27
26
27
28
27
5
µA
V
20
mV
20
0.2 0.4
V/µs
25°C
0.5 0.9
MHz
25°C
0.02
25°C
50
%
nV/√Hz
(1) The input common-mode voltage of either input should not be allowed to go below –0.3 V. The upper end of the common-mode voltage
range is V_CC+– 1.5 V, but either input can go to V_CC+ + 0.3 V (but ≤36 V) without damage.
5