SN74GTL16616_06 Datasheet, PDF (5/14 Pages) Texas Instruments – 17-BIT LVTTL-TO-GTL/GTL+ UNIVERSAL BUS TRANSCEIVER WITH BUFFERED CLOCK OUTPUTS

www.ti.com
SN74GTL16616
17-BIT LVTTL-TO-GTL/GTL+ UNIVERSAL BUS TRANSCEIVER
WITH BUFFERED CLOCK OUTPUTS
SCBS481H – JUNE 1994 – REVISED APRIL 2005
Electrical Characteristics
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER
V_IK
V_OH
A port
A port
V_OL
B port
Control inputs
A port
I_I
B port
I_off
I_I(hold) A port
A port
I_OZH
B port
A port
I_OZL
B port
I_CC
(3.3 V)
A or B port
I_CC
(5 V)
A or B port
∆I_CC ⁽³⁾
C_i
C_io
Control inputs
A port
B port
TEST CONDITIONS
V_CC (3.3 V) = 3.15 V, V_CC (5 V) = 4.75 V,
V_CC (3.3 V) = 3.15 V to 3.45 V,
V_CC (5 V) = 4.75 V to 5.25 V,
V_CC (3.3 V) = 3.15 V, V_CC (5 V) = 4.75 V
V_CC (3.3 V) = 3.15 V, V_CC (5 V) = 4.75 V
V_CC (3.3 V) = 3.15 V,
V_CC = 0 or 3.45 V,
V_CC (5 V) = 4.75 V,
V_CC (5 V) = 0 or 5.25 V,
V_CC (3.3 V) = 3.45 V, V_CC (5 V) = 5.25 V
V_CC (3.3 V) = 3.45 V,
V_CC = 0,
V_CC (5 V) = 5.25 V
V_I or V_O = 0 to 4.5 V
V_CC (3.3 V) = 3.15 V, V_CC (5 V) = 4.75 V
V_CC (3.3 V) = 3.45 V,
V_CC (3.3 V) = 3.45 V,
V_CC (3.3 V) = 3.45 V,
V_CC (3.3 V) = 3.45 V,
V_CC (5 V) = 5.25 V,
V_CC (5 V) = 5.25 V,
V_CC (5 V) = 5.25 V,
V_CC (5 V) = 5.25 V,
V_CC (3.3 V) = 3.45 V,
V_CC (5 V) = 5.25 V, I_O = 0,
V_I = V_CC (3.3 V) or GND
I_I = –18 mA
I_OH = –100 µA
I_OH = –8 mA
I_OH = –32 mA
I_OL = 100 µA
I_OL = 16 mA
I_OL = 32 mA
I_OL = 64 mA
I_OL = 40 mA
V_I = 5.5 V
V_I = 5.5 V
V_I = V_CC (3.3 V)
V_I = 0
V_I = V_CC (3.3 V)
V_I = 0
V_I = 0.8 V
V_I = 2 V
V_I = 0 to V_CC (3.3 V)⁽²⁾
V_O = 3 V
V_O = 1.2 V
V_O = 0.5 V
V_O = 0.4 V
Outputs high
Outputs low
Outputs disabled
V_CC (3.3 V) = 3.45 V,
V_CC (5 V) = 5.25 V, I_O = 0,
V_I = V_CC (3.3 V) or GND
Outputs high
Outputs low
Outputs disabled
V_CC (3.3 V) = 3.45 V, V_CC (5 V) = 5.25 V,
A-port or control inputs at V_CC (3.3 V) or GND, One input at 2.7 V
V_I = 3.15 V or 0
V_O = 3.15 V or 0
Per IEEE Std 1194.1
MIN TYP⁽¹⁾ MAX UNIT
–1.2 V
V_CC – 0.2
2.4
2
75
–75
V
0.2
0.4
0.5 V
0.55
0.4
10
20
1
µA
–30
5
–5
100 µA
µA
±500
1
µA
10
–1
µA
–10
1
5 mA
1
120
120 mA
120
1 mA
3.5
pF
12
pF
5
(1) All typical values are at V_CC (3.3 V) = 3.3 V, V_CC (5 V) = 5 V, T_A = 25°C.
(2) This is the bus-hold maximum dynamic current. It is the minimum overdrive current required to switch the input from one state to
another.
(3) This is the increase in supply current for each input that is at the specified TTL voltage level, rather than V_CC or GND.
5