SN74CB3Q6800 Datasheet, PDF (5/11 Pages) Texas Instruments – 10 BIT FET BUS SWITCH WITH PRECHAGED OUTPUTS 2.5V/3.3V LOW VOLTAGE HIGH BANDWIDTH BUS SWITCH

SN74CB3Q6800
10ĆBIT FET BUS SWITCH WITH PRECHARGED OUTPUTS
2.5ĆV/3.3ĆV LOWĆVOLTAGE HIGHĆBANDWIDTH BUS SWITCH
SCDS142A − OCTOBER 2003 − REVISED NOVEMBER 2003
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
MIN TYP† MAX UNIT
VIK
IIN
IO
IOZ‡
Ioff
ICC
∆ICC§
ICCD¶
Control inputs
B port
Control inputs
Per control
input
VCC = 3.6 V,
VCC = 3.6 V,
VCC = 3.V,
VCC = 3.6 V,
VCC = 0,
VCC = 3.6 V,
II = −18 mA
VIN = 0 to 5.5 V
BIASV = 2.4 V,
VO = 0,
VO = 0 to 5.5 V,
VI = 0,
VO = 0 to 5.5 V,
II/O = 0,
Switch ON or OFF,
VCC = 3.6 V,
One input at 3 V,
VCC = 3.6 V,
A and B ports open,
Control input switching at 50% duty cycle
Switch OFF,
VIN = VCC or GND
Switch OFF,
VIN = VCC or GND
VI = 0
VIN = VCC or GND
Other inputs at VCC or GND
−1.8 V
±1 µA
0.2
mA
±1 µA
1 µA
0.75
2 mA
30 µA
mA/
0.38 0.45 _MHz
Cin
Control inputs VCC = 3.3 V,
VIN = 5.5 V, 3.3 V, or 0
2.5 3.5 pF
Cio(OFF) A port
VCC = 3.3 V,
Switch OFF,
VIN = VCC or GND,
VI/O = 5.5 V, 3.3 V, or 0
3.5
5 pF
Cio(ON)
VCC = 3.3 V,
Switch ON,
VIN = VCC or GND, ^{VI/O = 5.5 V, 3.3 V, or 0}
9
11 pF
ron#
VCC = 2.3 V,
TYP at VCC = 2.5 V
VCC = 3 V
VI = 0,
VI = 1.7 V,
VI = 0,
VI = 2.4 V,
IO = 30 mA
IO = −15 mA
IO = 30 mA
IO = −15 mA
4.5
8
4.8
9
Ω
4.5
6
4.6
8
VIN and IIN refer to control inputs. VI, VO, II, and IO refer to data pins.
† _{All typical values are at VCC = 3.3 V (unless otherwise noted), TA = 25°C.}
‡ _{For I/O ports, the parameter IOZ includes the input leakage current.}
§ _{This is the increase in supply current for each input that is at the specified TTL voltage level, rather than VCC or GND.}
¶ _{This parameter specifies the dynamic power-supply current associated with the operating frequency of a single control input (see Figure 2).}
# _{Measured by the voltage drop between the A and B terminals at the indicated current through the switch. ON-state resistance is determined by}
the lower of the voltages of the two (A or B) terminals.
switching characteristics over recommended operating free-air temperature range (unless
otherwise noted) (see Figure 3)
PARAMETER
TEST CONDITIONS
FROM
(INPUT)
TO
(OUTPUT)
VCC = 2.5 V
± 0.2 V
MIN MAX
VCC = 3.3 V
± 0.3 V
MIN MAX
UNIT
fON||
tpd^k
ON
A or B
A or B
B or A
10
0.135
20 MHz
0.225 ns
tPZH
BIASV = GND
ON
tPZL
BIASV = 3 V
A or B
1.5 8.5 1.5 6.7
ns
1.5 8.5 1.5 6.7
tPHZ
BIASV = GND
ON
tPLZ
BIASV = 3 V
A or B
1
5
1 6.9
1
5
ns
1 6.9
|| _{Maximum switching frequency for control input (VO > VCC, VI = 5 V, RL ≥ 1 MΩ, CL = 0).}
k _{The propagation delay is the calculated RC time constant of the typical ON-state resistance of the switch and the specified load capacitance,}
when driven by an ideal voltage source (zero output impedance).
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265
5