SN74ALVCH16373_07 Datasheet, PDF (5/19 Pages) Texas Instruments – 16-BIT TRANSPARENT D-TYPE LATCH WITH 3-STATE OUTPUTS

www.ti.com
SN74ALVCH16373
16-BIT TRANSPARENT D-TYPE LATCH
WITH 3-STATE OUTPUTS
SCES020I – JULY 1995 – REVISED NOVEMBER 2005
Electrical Characteristics
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER
V_OH
I_OH = –100 µA
I_OH = –4 mA
I_OH = –6 mA
TEST CONDITIONS
I_OH = –12 mA
I_OH = –24 mA
I_OL = 100 µA
I_OL = 4 mA
V_OL
I_OL = 6 mA
I_OL = 12 mA
I_I
I_I(hold)
I_OZ
I_CC
∆I_CC
Control inputs
C_{i Data inputs}
C_o Outputs
I_OL = 24 mA
V_I = V_CC or GND
V_I = 0.58 V
V_I = 1.07 V
V_I = 0.7 V
V_I = 1.7 V
V_I = 0.8 V
V_I = 2 V
V_I = 0 to 3.6 V⁽²⁾
V_O = V_CC or GND
V_I = V_CC or GND
One input at V_CC – 0.6 V,
V_I = V_CC or GND
V_O = V_CC or GND
I_O = 0
Other inputs at V_CC or GND
V_CC
1.65 V to 3.6 V
1.65 V
2.3 V
2.3 V
2.7 V
3V
3V
1.65 V to 3.6 V
1.65 V
2.3 V
2.3 V
2.7 V
3V
3.6 V
1.65 V
1.65 V
2.3 V
2.3 V
3V
3V
3.6 V
3.6 V
3.6 V
3 V to 3.6 V
3.3 V
3.3 V
MIN TYP⁽¹⁾
V_CC – 0.2
1.2
2
1.7
2.2
2.4
2
25
–25
45
–45
75
–75
3
6
7
MAX
0.2
0.45
0.4
0.7
0.4
0.55
±5
±500
±10
40
750
UNIT
V
V
µA
µA
µA
µA
µA
pF
pF
(1) All typical values are at V_CC = 3.3 V, T_A = 25°C.
(2) This is the bus-hold maximum dynamic current. It is the minimum overdrive current required to switch the input from one state to
another.
Timing Requirements
over recommended operating free-air temperature range (unless otherwise noted) (see Figure 1)
t_w
Pulse duration, LE high or low
t_su
Setup time, data before LE↓
t_h
Hold time, data after LE↓
V_CC = 1.8 V
MIN
(1)
MAX
(1)
(1)
V_CC = 2.5 V
± 0.2 V
MIN MAX
3.3
1
1.5
V_CC = 2.7 V
MIN MAX
3.3
1
1.7
(1) This information was not available at the time of publication.
V_CC = 3.3 V
± 0.3 V
MIN MAX
3.3
1.1
1.4
UNIT
ns
ns
ns
5