CLV4051ATDWRG4Q1 Datasheet, PDF (5/18 Pages) Texas Instruments – 8-CHANNEL ANALOG MULTIPLEXER/DEMULTIPLEXER

SN74LV4051A-Q1
www.ti.com
SCLS520D – AUGUST 2003 – REVISED JUNE 2011
SWITCHING CHARACTERISTICS
V_CC = 3.3 V ± 0.3 V, over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
TEST
CONDITIONS
T_A = 25°C
MIN TYP MAX
T_A = -40 to
105°C
MIN MAX
T_A = -40 to
125°C
MIN MAX
t_{PLH Propagation}
t_PHL ^{delay time}
COM or Yn Yn or COM
C_L = 50 pF
(see Figure 4)
2.5
9
12
14
t_{PZH Enable delay}
t_PZL ^time
INH
COM or Yn
C_L = 50 pF
(see Figure 5)
5.5 20
25
25
t_{PHZ Disable delay}
t_PLZ ^time
INH
COM or Yn
C_L = 50 pF
(see Figure 5)
8.8 20
25
25
UNIT
ns
ns
ns
SWITCHING CHARACTERISTICS
V_CC = 5 V ± 0.5 V, over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
TEST
CONDITIONS
T_A = 25°C
MIN TYP MAX
T_A = -40 to
105°C
MIN
MAX
T_A = -40 to
125°C
MIN
MAX
t_{PLH Propagation}
t_PHL ^{delay time}
COM or Yn
Yn or COM
C_L = 50 pF
(see Figure 4)
1.5 6
8
10
t_{PZH Enable delay}
t_PZL ^time
INH
COM or Yn
C_L = 50 pF
(see Figure 5)
4 14
18
18
t_{PHZ Disable delay}
t_PLZ ^time
INH
COM or Yn
C_L = 50 pF
(see Figure 5)
6.2 14
18
18
UNIT
ns
ns
ns
ANALOG SWITCH CHARACTERISTICS
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
TEST CONDITIONS
V_CC
Frequency response
(switch on)
COM or Yn
Crosstalk
(control input to signal
INH
output)
Feedthrough
attenuation
(switch off)
COM or Yn
Sine-wave distortion
COM or Yn
Yn or COM
COM or Yn
Yn or COM
Yn or COM
C_L = 50 pF,
R_L = 600 Ω,
f_in = 1 MHz (sine wave)⁽¹⁾
(see Figure 6)
C_L = 50 pF,
R_L = 600 Ω,
f_in = 1 MHz (square wave)
(seeFigure 7 )
C_L = 50 pF,
R_L = 600 Ω,
f_in = 1 MHz⁽²⁾
(see Figure 8)
C_L = 50 pF,
R_L = 10 kΩ,
f_in = 1 kkHz (sine
wave)
(see Figure 9)
V_I = 2 Vp-p
V_I = 2.5 Vp-p
V_I = 4 Vp-p
2.3 V
3V
4.5 V
2.3 V
3V
4.5 V
2.3 V
3V
4.5 V
2.3 V
3V
4.5 V
(1) Adjust f_in voltage to obtain 0-dBm output. Increase fin frequency until dB meter reads −3 dB.
(2) Adjust f_in voltage to obtain 0-dBm input.
T_A = 25°C
MIN TYP
20
25
35
20
35
60
–45
–45
–45
0.1
0.1
0.1
MAX
UNIT
MHz
mV
dB
%
OPERATING CHARACTERISTICS
V_CC = 3.3 V, T_A = 25°C (unless otherwise noted)
PARAMETER
C_pd Power dissipation capacitance
TEST CONDITIONS
C_L = 50 pF, f = 10 MHz
TYP UNIT
5.9 pF
Copyright © 2003–2011, Texas Instruments Incorporated
5