CLV4051ATDWRG4Q1 Datasheet, PDF (3/18 Pages) Texas Instruments – 8-CHANNEL ANALOG MULTIPLEXER/DEMULTIPLEXER

SN74LV4051A-Q1
www.ti.com
SCLS520D – AUGUST 2003 – REVISED JUNE 2011
ABSOLUTE MAXIMUM RATINGS⁽¹⁾
over operating free-air temperature range (unless otherwise noted)
V_CC Supply voltage range
V_I
Input voltage range⁽²⁾
V_IO
Switch I/O voltage range^{(2) (3)}
I_IK
Input clamp current
V_I < 0
I_IOK I/O diode current
V_IO < 0
I_T
Switch through current
V_IO = 0 to V_CC
Continuous current through V_CC or GND
D package
θ_JA
Package thermal impedance, junction to free air⁽⁴⁾ DW package
PW package
–0.5 V to 7 V
–0.5 V to 7 V
–0.5 V to V_CC + 0.5 V
–20 mA
–50 mA
±25 mA
±50 mA
95°C/W
75°C/W
108°C/W
T_stg Storage temperature range
–65°C to 150°C
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
(3) This value is limited to 5.5 V maximum.
(4) The package thermal impedance is calculated in accordance with JESD 51-7.
RECOMMENDED OPERATING CONDITIONS⁽¹⁾
V_CC Supply voltage
V_IH High-level input voltage
V_IL
Low-level input voltage
V_I
Control input voltage
V_IO Input/output voltage
Δt/Δv Input transition rise or fall rate
T_A
Operating free-air temperature
V_CC = 2 V
V_CC = 2.3 V to 2.7 V
V_CC = 3 V to 3.6 V
V_CC = 4.5 V to 5.5 V
V_CC = 2 V
V_CC = 2.3 V to 2.7 V
V_CC = 3 V to 3.6 V
V_CC = 4.5 V to 5.5 V
V_CC = 2.3 V to 2.7 V
V_CC = 3 V to 3.6 V
V_CC = 4.5 V to 5.5 V
SN74LV4051ATDRQ1,SN74LV4051ATDWRQ1
SN74LV4051ATPWRQ1
MIN
MAX
2 ⁽²⁾
5.5
1.5
V_CC × 0.7
V_CC × 0.7
V_CC × 0.7
0.5
V_CC × 0.3
V_CC × 0.3
V_CC × 0.3
0
5.5
0
V_CC
200
100
20
UNIT
V
V
V
V
V
ns/V
–40
105
°C
T_A
Operating free-air temperature
SN74LV4051AQPWRQ1
–40
125
(1) All unused inputs of the device must be held at V_CC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
(2) With supply voltages at or near 2 V, the analog switch on-state resistance becomes very nonlinear. It is recommended that only digital
signals be transmitted at these low supply voltages.
Copyright © 2003–2011, Texas Instruments Incorporated
3