OPA452 Datasheet, PDF (4/17 Pages) Texas Instruments – 80V, 50mA OPERATIONAL AMPLIFIERS

ELECTRICAL CHARACTERISTICS: OPA453; V_S = ±10V to ±40V
Boldface limits apply over the specified junction temperature range, T_J = –40°C to +125°C.
At T_J = +25°C, R_L = 3.8kΩ connected to ground, and V_OUT = 0V, unless otherwise noted.
PARAMETER
CONDITION
OPA453TA, FA
MIN
TYP
MAX
UNITS
OFFSET VOLTAGE
Input Offset Voltage
over Temperature
Drift
vs Power Supply
over Temperature
INPUT BIAS CURRENT⁽¹⁾
Input Bias Current
Input Offset Current
NOISE
Input Voltage Noise Density
Current Noise Density
INPUT VOLTAGE RANGE
Common-Mode Voltage Range
Common-Mode Rejection Ratio
over Temperature
INPUT IMPEDANCE
Differential
Common-Mode
OPEN-LOOP GAIN
Open-Loop Voltage Gain
over Temperature
over Temperature
FREQUENCY RESPONSE
Gain-Bandwidth Product
Slew Rate
Settling Time: 0.1%
0.01%
Overload Recovery Time
Total Harmonic Distortion + Noise
OUTPUT
Voltage Output
over Temperature
Voltage Output
over Temperature
Output Current
Short-Circuit Current
Capacitive Load Drive
SHUTDOWN FLAG
Thermal Shutdown Status Output
Normal Operation
Thermally Shutdown
Junction Temperature
Shutdown
Reset from Shutdown
POWER SUPPLY
Supply Voltage Range
Quiescent Current (per amplifier)
over Temperature
TEMPERATURE RANGE
Specified Range (junction)
Operating Range (junction)
Storage Range (ambient)
Thermal Resistance
TO200-7
DDPAK-7
V_OS
dV_OS/ dT
PSRR
V_S = ±40V, V_CM = 0V, I_O = 0V
V_S = ±10V to ±40V, V_CM = 0V
±1
±3
±6
±5
5
30
45
I_B
V_S = ±40V, V_CM = 0V
I_OS
V_S = ±40V, V_CM = 0V
±7
±100
±1
±100
e_n
f = 1kHz
21
i_n
f = 1kHz
9
V_CM
CMRR
V_S = ±40V, –35V < V_CM < 39.5V
V_S = ±40V, –35V < V_CM < 39.5V
(V–) + 5
86
76
(V+) – 0.5
94
V_S = ±40V, –35V < V_CM < 39.5V
10¹³ || 2
10¹³ || 6
A_OL I_O = 10mA, –V_S + 2V < V_O < +V_S – 2V
105
110
I_O = 10mA, –V_S + 2V < V_O < +V_S – 2V
107
I_O = 50mA, –V_S + 4V < V_O < +V_S – 4V
96
110
I_O = 50mA, –V_S + 5V < V_O < +V_S – 5.5V
105
GBW
SR
THD+N
V_S = ±40V
V_S = ±40V
V_S = ±40V, G = +5, 10V Step, C_L = 100pF
V_S = ±40V, G = +5, 10V Step, C_L = 100pF
V_IN • Gain = V_S
V_S = ±40V, V_O = 30Vp-p, G = 5
f = 1kHz, R_L = 2kΩ
7.5
+23 / –38
1
1.5
1
0.0008
V_OUT
I_SC
C_LOAD
I_O = 50mA
I_O = 50mA
I_O = 10mA
I_O = 10mA
(V–) + 4.0
(V+) – 4
(V–) + 5
(V+) – 5.5
(V–) + 2
(V+) – 2
(V–) + 2
(V+) – 2
±50
±125
See Typical Characteristic
V_S = ±40V
V_S = ±40V
V_S
I_Q
I_O = 0
T_J
T_J
T_A
θ_JC
0.1
1.0
100
140
165
+160
+145
±10
±40
±5.5
±6.5
±7.5
–40
+125
–55
+125
–65
+150
3
3
mV
mV
µV/°C
µV/V
µV/V
pA
pA
nV/^√Hz
fA/^√Hz
V
dB
dB
Ω || pF
Ω || pF
dB
dB
dB
dB
MHz
V/µs
µs
µs
µs
%
V
V
V
V
mA
mA
µA
µA
°C
°C
V
mA
mA
°C
°C
°C
°C/W
°C/W
NOTE: (1) All tests are high-speed tested at +25°C ambient temperature. Effective junction temperature is +25°C, unless otherwise noted.
4
OPA452, 453
www.ti.com
SBOS127C