TLC5923 Datasheet, PDF (3/15 Pages) Texas Instruments – LED DRIVER

www.ti.com
AC Characteristics
V_CC = 3 V to 5.5 V, T_A = -20°C to 85°C (unless otherwise noted)
f_SCLK
t_wh0/t_wl0
t_wh1
t_su0
t_su1
t_su2
t_su3
t_h0
t_h1
t_h2
t_h3
Clock frequency
CLK pulse duration
XLAT pulse duration
Setup time
Hold time
SCLK
SCLK=H/L
XLAT=H
SIN - SCLK↑
SCLK↑-XLAT↓
MODE↑↓-SCLK↑
MODE↑↓-XLAT↓
SCLK↑-SIN
XLAT↓-SCLK↑
SCLK↑-MODE↑↓
XLAT↓-MODE↑↓
TLC5923
SLVS550 – DECEMBER 2004
MIN
TYP
MAX UNIT
30 MHz
16
ns
20
ns
10
ns
10
ns
10
ns
10
ns
10
ns
10
ns
10
ns
10
ns
ELECTRICAL CHARACTERISTICS
V_CC = 3 V to 5.5 V, T_A = - 20°C to 85°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
V_OH
High-level output voltage
I_OH = - 1 mA, SOUT
V_CC -0.5
V_OL
Low-level output voltage
I_OL = 1 mA, SOUT
I_I
Input current
V_I = V_CC or GND, BLANK, XLAT, SCLK, SIN,
MODE
-1
V
0.5
V
1 µA
I_CC
Supply current
I_OLC
I_LO0
I_LO1
∆I_OLC0
Constant output current
Leakage output current
Constant current error
No data transfer, All output OFF, V_O = 1 V,
R_(IREF) = 10 kΩ
No data transfer, All output OFF, V_O = 1 V,
R_(IREF) = 1.3 kΩ
Data transfer 30 MHz, All output ON, V_O = 1 V,
R_(IREF) = 1.3 kΩ
Data transfer 30 MHz, All output ON, V_O = 1 V,
R_(IREF) = 600 kΩ
All output ON, V_O = 1 V, R_(IREF) = 600 Ω
All output OFF, V_O = 15 V, R_(IREF) = 600 Ω ,
OUT0 to OUT15
V_XERR = 5.5 V, No TEF and LOD
All output ON, V_O = 1 V, R_(IREF) = 600 Ω,
OUT0 to OUT15
6
12
mA
25
36
65 ⁽¹⁾
70
80
90 mA
0.1 µA
10 µA
±1
±4
%
∆I_OLC1
∆I_OLC2
Constant current error
Power supply rejection ratio
device to device, averaged current from OUT0
to OUT15, R_(IREF) = 600 Ω
All output ON, V_O = 1 V, R_(IREF) = 600 Ω,
OUT0 to OUT15
±4
± 8.5
%
±1
± 4 %/V
∆I_OLC3
T_(TEF)
V_(LOD)
Load regulation
Thermal error flag threshold
LED open detection
threshold
All output ON, V_O = 1 V to 3 V, R_(IREF) = 600
Ω,
OUT0 to OUT15
Junction temperature, rising temperature⁽²⁾
±2
± 6 %/V
150
160
180
°C
0.3
0.4
V
V_(IREF) Reference voltage output
R_(IREF) = 600 Ω
1.20
1.24
1.28
V
(1) Measured at device start-up temperature. Once the IC is operating (self heating), lower I_CC values will be seen. See Figure 15.
(2) Not tested. Specified by design.
3