SN75HVD10DRG4 Datasheet, PDF (3/28 Pages) Texas Instruments – Optional Driver Output Transition Times for Signaling Rates (1) of 1 Mbps, 10 Mbps, and 32 mbps

www.ti.com
SN65HVD10, SN65HVD10Q, SN75HVD10
SN65HVD11, SN65HVD11Q, SN75HVD11
SN65HVD12, SN75HVD12
SLLS505K – FEBRUARY 2002 – REVISED SEPTEMBER 2011
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range unless otherwise noted
MIN
NOM
MAX UNIT
V_CC
V_I or V_IC
V_IH
V_IL
V_ID
I_OH
Supply voltage
Voltage at any bus terminal (separately or common mode)
High-level input voltage
D, DE, RE
Low-level input voltage
D, DE, RE
Differential input voltage
Figure 7
High-level output current
Driver
Receiver
3
–7 ⁽¹⁾
2
0
–12
–60
–8
3.6
12
V_CC
V
0.8
12
mA
I_OL
Low-level output current
Driver
Receiver
60
mA
8
R_L
Differential load resistance
C_L
Differential load capacitance
HVD10
54
60
Ω
50
pF
32
Signaling rate
HVD11
10 Mbps
T_J ⁽²⁾
Junction temperature
HVD12
1
145 °C
(1) The algebraic convention, in which the least positive (most negative) limit is designated as minimum is used in this data sheet.
(2) See thermal characteristics table for information regarding this specification.
DRIVER ELECTRICAL CHARACTERISTICS
over recommended operating conditions unless otherwise noted
PARAMETER
TEST CONDITIONS
V_IK
|V_OD|
Δ|V_OD|
Input clamp voltage
Differential output voltage⁽²⁾
Change in magnitude of differential output
voltage
I_I = –18 mA
I_O = 0
R_L = 54 Ω, See Figure 1
V_test = –7 V to 12 V, See Figure 2
See Figure 1 and Figure 2
V_OC(PP)
V_OC(SS)
ΔV_OC(SS)
Peak-to-peak common-mode output voltage
Steady-state common-mode output voltage
Change in steady-state common-mode output
voltage
See Figure 3
I_OZ
High-impedance output current
See receiver input currents
D
I_I
Input current
DE
I_OS
C_(OD)
Short-circuit output current
Differential output capacitance
–7 V ≤ V_O ≤ 12 V
V_OD = 0.4 sin (4E6πt) + 0.5 V, DE at 0 V
RE at V_CC,
D & DE at V_CC,
No load
Receiver disabled and
driver enabled
I_CC
Supply current
RE at V_CC,
D at V_CC,
DE at 0 V,
No load
Receiver disabled and
driver disabled (standby)
RE at 0 V,
D & DE at V_CC,
No load
Receiver enabled and
driver enabled
(1) All typical values are at 25°C and with a 3.3-V supply.
(2) For T_A > 85°C, V_CC is ±5%.
MIN TYP⁽¹⁾ MAX UNIT
–1.5
V
2
V_CC
1.5
V
1.5
–0.2
0.2 V
400
mV
1.4
2.5 V
–0.0
5
0.05 V
–100
0
–250
0
μA
100
250 mA
16
pF
9 15.5 mA
1
5 μA
9 15.5 mA
Copyright © 2002–2011, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): SN65HVD10, SN65HVD10Q, SN75HVD10 SN65HVD11, SN65HVD11Q, SN75HVD11
SN65HVD12, SN75HVD12