CDC351DBR Datasheet, PDF (3/13 Pages) Texas Instruments – 1-LINE TO 10-LINE CLOCK DRIVER WITH 3-STATE OUTPUTS

www.ti.com
CDC351. CDC351I
1-LINE TO 10-LINE CLOCK DRIVER WITH 3-STATE OUTPUTS
SCAS441D – FEBRUARY 1994 – REVISED OCTOBER 2003
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted) ⁽¹⁾
Supply voltage range, V_CC
Input voltage range, V_I ⁽²⁾
Voltage range applied to any output in the
high state or power-off state,
V_O ⁽²⁾
Current into any output in the low state, I_O
Input clamp current, I_IK(V_I < 0)
Output clamp current, I_OK (V_I < 0)
Package thermal impedance Θ_JA ^(3):
DB package
DW package
Storage temperature range, T_stg
– 0.5 V to 4.6 V
– 0.5 V to 7 V
– 0.5 V to 3.6 V
64 mA
– 18 mA
– 50 mA
147°C/ W
101°C/ W
– 65°C to 150°C
(1) _{Stresses beyond those listed under,, absolute maximum ratings” may cause permanent damage to the device. These are stress}
ratings only, and functional operation of the device at these or any other conditions beyond those indicated under,, recommended
operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) _{The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.}
(3) _{The package thermal impedance is calculated in accordance with JESD51.}
RECOMMENDED OPERATING CONDITIONS ⁽¹⁾
V_CC
V_IH
V_IL
V_I
I_OH
I_OL
f_clock
T_A
Supply voltage
High-level input voltage
Low-level input voltage
Input voltage
High-level output current
Low-level output current
Input clock frequency
Operating free-air temperature
Commercial
Industrial
MIN MAX UNIT
3 3.6 V
2
V
0.8 V
0 5.5 V
– 32 mA
32 mA
100 MHz
0
70 °C
– 40
85 °C
(1) _{Unused pins (input or I/O) must be held high or low.}
ELECTRICAL CHARACTERISTICS
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER
V_IK
V_OH
V_OL
I_I
I_O ⁽¹⁾
I_OZ
I_CC
C_i
C_o
TEST CONDITIONS
V_CC = 3 V,
V_CC = 3 V,
V_CC = 3 V,
V_CC = 3.6 V,
V_CC = 3.6 V,
V_CC = 3.6 V,
I_I = –18 mA
I_OH = –32 mA
I_OL = 32 mA
V_I = V_CC or GND
V_O = 2.5 V
V_O = 3 V or 0
V_CC = 3.6 V, I_O = 0, V_I = V_CC or GND
V_I = V_CC or GND,
V_O = V_CC or GND,
V_CC = 3.3 V,
V_CC = 3.3 V,
Outputs high
Outputs low
Outputs disabled
f = 10 MHz
f = 10 MHz
MIN TYP MAX UNIT
–1.2 V
2
V
0.5 V
±1 µA
–15
–150 mA
±10 µA
0.3
25 mA
0.3
4
pF
6
pF
(1) _{Not more than one output should be tested at a time, and the duration of the test should not exceed one second.}
3