CD74FCT823A Datasheet, PDF (3/7 Pages) Texas Instruments – BiCMOS FCT Interface Logic, 9-Bit D-Type Flip-Flops, Three-State

CD74FCT823A, CD74FCT824A
Absolute Maximum Ratings
DC Supply Voltage (V_CC) . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 6V
DC Diode Current, I_IK (For V_I < -0.5V) . . . . . . . . . . . . . . . . . . -20mA
DC Output Diode Current, I_OK (for V_O < -0.5V) . . . . . . . . . . . -50mA
DC Output Sink Current per Output Pin, IO . . . . . . . . . . . . . . . 70mA
DC Output Source Current per Output Pin, IO . . . . . . . . . . . . -30mA
DC V_CC Current (I_CC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234mA
DC Ground Current (I_GND). . . . . . . . . . . . . . . . . . . . . . . . . . . 453mA
Thermal Information
Thermal Resistance (Typical, Note 2)
θ_JA (^oC/W)
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150^oC
Maximum Storage Temperature Range . . . . . . . . . .-65^oC to 150^oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300^oC
Operating Conditions
Operating Temperature Range, T_A . . . . . . . . . . . . . . . . .0^oC to 70^oC
Supply Voltage Range, V_CC . . . . . . . . . . . . . . . . . . . .4.75V to 5.25V
DC Input Voltage, V_I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to V_CC
DC Output Voltage, V_O . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to ≤ V_CC
Input Rise and Fall Slew Rate, dt/dv. . . . . . . . . . . . . . . . 0 to 10ns/V
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
2. θ_JA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications Commercial Temperature Range 0^oC to 70^oC, V_CC Max = 5.25V, V_CC Min = 4.75V
TEST CONDITIONS
AMBIENT TEMPERATURE (T_A)
25^oC
0^oC TO 70^oC
PARAMETER
High Level Input Voltage
Low Level Input Voltage
High Level Output Voltage
Low Level Output Voltage
High Level Input Current
Low Level Input Current
Three-State Leakage Current
Input Clamp Voltage
SYMBOL V_I (V)
I_O (mA)
V_CC (V)
MIN MAX MIN MAX UNITS
V_IH
4.75 to 5.25 2
-
2
-
V
V_IL
4.75 to 5.25 -
0.8
-
0.8
V
V_OH
V_IH or V_IL
-15
Min
2.4
-
2.4
-
V
V_OL
V_IH or V_IL
48
Min
-
0.55
-
0.55
V
I_IH
V_CC
Max
-
0.1
-
1
µA
I_IL
GND
Max
-
-0.1
-
-1
µA
I_OZH
V_CC
Max
-
0.5
-
10
µA
I_OZL
GND
Max
-
-0.5
-
-10
µA
V_IK
V_CC or
-18
Min
-
-1.2
-
-1.2
V
GND
Short Circuit Output Current
(Note 3)
I_OS
V_O = 0
V_CC or
GND
Max
-75
-
-75
-
mA
Quiescent Supply Current,
MSI
I_CC
V_CC or
0
GND
Max
-
8
-
80
µA
Additional Quiescent Supply
Current per Input Pin
TTL Inputs High, 1 Unit Load
∆I_CC
3.4V
(Note 4)
Max
-
1.6
-
1.6
mA
NOTES:
3. Not more than one output should be shorted at one time. Test duration should not exceed 100ms.
4. Inputs that are not measured are at V_CC or GND.
5. FCT Input Loading: All inputs are 1 unit load. Unit load is ∆I_CC limit specified in Electrical Specifications table, e.g., 1.6mA Max. at 70^oC.
8-3