AMC7820 Datasheet, PDF (3/28 Pages) Texas Instruments – ANALOG MONITORING AND CONTROL

ELECTRICAL CHARACTERISTICS (Cont.)
At –40°C to +85°C, AV_DD, DV_DD, BV_DD = +5V, using external 2.5V reference, unless otherwise noted.
PARAMETER
CONDITION
MIN
AMC7820
TYP
MAX
UNITS
VOLTAGE REFERENCE (V_REF)
Internal Reference Voltage
Internal Reference Drift⁽⁵⁾
2.5V Output Impedance (pin 26)
2.5V Output Current (pin 26)
Short-Circuit Current (pin 26)
External Reference Voltage Range (pin 27)
External Reference Input Resistance
External Reference Input Capacitance
OP AMP CHARACTERISTICS⁽⁶⁾
Input Offset Voltage
vs Temperature
vs Power Supply
Input Bias Current⁽⁷⁾
Input Offset Current⁽⁷⁾
Input Voltage Noise
Input Voltage Noise Density
Current Noise Density
Common-Mode Voltage Range
Common-Mode Rejection Ratio⁽⁸⁾
Open-Loop Gain⁽⁸⁾
Gain-Bandwidth Product
Slew Rate
Settling Time: 0.1%
Voltage Output Swing from Rail
Closed-Loop Output Impedance
Output Current
Short-Circuit Current
DIGITAL INPUT/OUTPUT
Logic Level:
V_IH
V_IL
V_OH
V_OL
Logic Level:
V_IH
V_IL
V_OH
V_OL
Input Capacitance
POWER-SUPPLY REQUIREMENTS
Power-Supply Voltage
AV_DD, DV_DD
BV_DD
Quiescent Current of AV_DD
Quiescent Current of DV_DD
Quiescent Current of BV_DD
Power Dissipation
TEMPERATURE RANGE
Specified Performance
Storage
0°C to +85°C
–40°C to +85°C
T_A = +25°C
T_A = –40°C to +85°C
T_A = +25°C
f = 0.1Hz to 10Hz
f = 1kHz
f = 1kHz
–0.2V < V_CM < AV_DD – 1.2V
R_L = 25kΩ, 125mV < V_O < AV_DD – 125mV
G=1
G=1
2V Step, C_L = 100pF, G = 1, R_L = 10kΩ
R_L = 25kΩ
See Typical Characteristics
BV_DD = 5V, |I_IH| ≤ 10µA
BV_DD = 5V, |I_IL| ≤ 10µA
BV_DD = 5V, I_OH = –3mA
BV_DD = 5V, I_OL = 3mA
BV_DD = 3V, |I_IH| ≤ 10µA
BV_DD = 3V, |I_IL| ≤ 10µA
BV_DD = 3V, I_OH = –3mA
BV_DD = 3V, I_OL = 3mA
Specified Performance
Specified Performance
2.45
2.50
2.55
±10
±30
0.5
±1
±15
2.45
2.50
2.55
10
5
±0.5
±4
±2
50
±2
±50
See Typical Characteristics
±1
±50
6
26
0.6
–0.2
74
AV_DD – 1.2
90
100
120
3
1.2
3
40
0.4
±1
±18
3.5
BV_DD + 0.3
0
0.8
4.0
BV_DD
0
0.4
2.1
BV_DD + 0.3
0
0.6
2.4
BV_DD
0
0.4
5
4.75
5
5.25
2.7
5.25
8
12
0.3
0.75
0.01
0.1
40
–40
+85
–65
+150
V
ppm/°C
ppm/°C
Ω
mA
mA
V
kΩ
pF
mV
µV/°C
µV/V
pA
pA
µVp-p
nV/√Hz
fA/√Hz
V
dB
dB
MHz
V/µs
µs
mV
Ω
mA
mA
V
V
V
V
V
V
V
V
pF
V
V
mA
mA
mA
mW
°C
°C
NOTES: (1) For channels 2-5, fed into MUX directly. (2) LSB means Least Significant Bit. (3) DACs are tested without output load. (4) Measured from code 010
to FFF. (5) Internal reference voltage has been optimized for lowest drift from 0°C to +85°C. (6) Applies to all amplifiers; see Figure 2. (7) Offset current will double
for each 10°C of temperature increase. See Operational Amplifier section. (8) Ensured by design.
AMC7820
3
SBAS231B
www.ti.com