SN74CBTS6800 Datasheet, PDF (2/4 Pages) Texas Instruments – 10-BIT FET BUS SWITCH WITH PRECHARGED OUTPUTS AND SCHOTTKY DIODE CLAMPING

SN74CBTS6800
10-BIT FET BUS SWITCH
WITH PRECHARGED OUTPUTS AND SCHOTTKY DIODE CLAMPING
SCDS102A – JUNE 1999 – REVISED JULY 1999
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)^†
Supply voltage range, V_CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V
Bias voltage range, BIASV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V
Input voltage range, V_I (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V
Continuous channel current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA
Input clamp current, I_IK (V_I < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA
Package thermal impedance, θ_JA (see Note 2): DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104°C/W
DBQ package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103°C/W
DGV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139°C/W
DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81°C/W
PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120°C/W
Storage temperature range, T_stg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
† _{Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and}
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
2. The package thermal impedance is calculated in accordance with JESD 51.
recommended operating conditions (see Note 3)
MIN MAX UNIT
VCC Supply voltage
4 5.5 V
BIASV Supply voltage
1.3 VCC V
VIH High-level control input voltage
2
V
VIL
Low-level control input voltage
TA
Operating free-air temperature
0.8 V
–40
85 °C
NOTE 3: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
MIN TYP‡ MAX UNIT
A or B inputs
VIK
Control inputs ^{VCC = 4.5 V,}
II = –18 mA
–0.7
V
–1.2
IIL
IIH
IO
ICC
∆ICC§
Control inputs
Ci
Control inputs
Cio(OFF)
VCC = 5.5 V,
VCC = 5.5 V,
VCC = 4.5 V,
VCC = 5.5 V,
VCC = 5.5 V,
VI = 3 V or 0
VO = 3 V or 0,
VI = GND
VI = 5.5 V
BIASV = 2.4 V,
IO = 0,
One input at 3.4 V,
VO= 0
VI = VCC or GND
Other inputs at VCC or GND
ON = VCC
0.25
–5 µA
150 µA
mA
3 µA
2.5 mA
3.5
pF
4.5
pF
VCC = 4 V,
TYP at VCC = 4 V
VI = 2.4 V,
II = 15 mA
11
20
ron¶
VCC = 4.5 V
VI = 0
II = 64 mA
II = 30 mA
3
7Ω
3
7
VI = 2.4 V,
II = 15 mA
6
15
‡ _{All typical values are at VCC = 5 V (unless otherwise noted), TA = 25°C.}
§ _{This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND.}
¶ _{Measured by the voltage drop between the A and B terminals at the indicated current through the switch. On-state resistance is determined by}
the lower of the voltages of the two (A or B) terminals.
2
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265