TLE207XA Datasheet, PDF (16/81 Pages) Texas Instruments – EXCALIBUR LOW-NOISE HIGH-SPEED JFET-INPUT OPERATIONAL AMPLIFIERS

TLE207x, TLE207xA
ą
EXCALIBUR LOWĆNOISE HIGHĆSPEED
JFETĆINPUT OPERATIONAL AMPLIFIERS
SLOS181B − FEBRUARY 1997 − REVISED APRIL 2004
TLE2071M electrical characteristics at specified free-air temperature, V_CC± = ±5 V (unless
otherwise noted)
PARAMETER
ICC Supply current
IOS
Short-circuit output
current
† _{Full range is − 55°C to 125°C.}
TEST CONDITIONS
VO = 0,
VO = 0
No load
VID = 1 V
VID = − 1 V
TA†
25°C
Full range
25°C
TLE2071M
MIN TYP MAX
1.35 1.6 2.2
2.2
− 35
45
TLE2071AM
MIN TYP MAX
1.35 1.6 2.2
2.2
− 35
45
UNIT
mA
mA
TLE2071M operating characteristics at specified free-air temperature, V_CC± = ±5 V
PARAMETER
SR +
Positive slew rate
SR −
Negative slew rate
TEST CONDITIONS
VO(PP) = ± 2.3 V,
AVD = − 1,
RL = 2 kΩ,
CL = 100 pF, See Figure 1
TA†
25°C
Full
range
25°C
Full
range
TLE2071M
MIN TYP MAX
35
20^}
38
20^}
TLE2071AM
MIN TYP MAX
35
20^}
UNIT
V/µs
38
20^}
V/µs
ts
Vn
VN(PP)
Settling time
Equivalent input noise
voltage
Peak-to-peak equivalent
input noise voltage
AVD = − 1,
2-V step,
RL = 1 kΩ,
CL = 100 pF
RS = 20 Ω,
See Figure 3
To 10 mV
To 1 mV
f = 10 Hz
f = 10 kHz
f = 10 Hz to
10 kHz
f = 0.1 Hz to
10 Hz
25°C
25°C
25°C
0.25
0.4
28 55^}
11.6 17^}
6
0.6
0.25
µs
0.4
28 55^}
11.6 17^{} nV/√Hz}
6
µV
0.6
In
Equivalent input noise
current
VIC = 0,
f = 10 kHz
25°C
2.8
2.8
fA/√Hz
Total harmonic distortion
THD + N _{plus noise}
VO(PP) = 5 V,
f = 1 kHz,
RS = 25 Ω
AVD = 10,
RL = 2 kΩ,
25°C
0.013%
B1
Unity-gain bandwidth
VI = 10 mV,
CL = 25 pF,
RL = 2 kΩ,
See Figure 2
25°C
9.4
BOM
Maximum output-swing
bandwidth
VO(PP) = 4 V, AVD = − 1,
RL = 2 kΩ , CL = 25 pF
25°C
2.8
φ_m
Phase margin at unity
gain
VI = 10 mV,
CL = 25 pF,
RL = 2 kΩ,
See Figure 2
25°C
56°
† _{Full range is − 55°C to 125°C.}
‡ ∗_{On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.}
0.013%
9.4
2.8
56°
MHz
MHz
16
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265