LP2951-50QDRGRQ1 Datasheet, PDF (14/24 Pages) Texas Instruments – ADJUSTABLE MICROPOWER VOLTAGE REGULATORS WITH SHUTDOWN

LP2951-33-Q1
LP2951-50-Q1
SLVSAW6D – JUNE 2011 – REVISED APRIL 2013
www.ti.com
Capacitor Types
Most tantalum or aluminum electrolytics are suitable for use at the input. Film-type capacitors also work, but at
higher cost. When operating at low temperature, care should be taken with aluminum electrolytics, as their
electrolytes often freeze at –30°C. For this reason, solid tantalum capacitors should be used at temperatures
below –25°C.
Ceramic capacitors can be used, but due to their low ESR (as low as 5 mΩ to 10 mΩ), they may not meet the
minimum ESR requirement previously discussed. If a ceramic capacitor is used, a series resistor between 0.1 Ω
to 2 Ω must be added to meet the minimum ESR requirement. In addition, ceramic capacitors have one glaring
disadvantage that must be taken into account — a poor temperature coefficient, where the capacitance can vary
significantly with temperature. For instance, a large-value ceramic capacitor (≥2.2 μF) can lose more than half of
its capacitance as temperature rises from 25°C to 85°C. Thus, a 2.2-μF capacitor at 25°C drops well below the
minimum C_OUT required for stability as ambient temperature rises. For this reason, select an output capacitor that
maintains the minimum 2.2 μF required for stability for the entire operating temperature range.
C_BYPASS: Noise and Stability Improvement
In the LP2951-xx-Q1, an external FEEDBACK pin directly connected to the error amplifier noninverting input can
allow stray capacitance to cause instability by shunting the error amplifier feedback to GND, especially at high
frequencies. This is worsened if high-value external resistors are used to set the output voltage, because a high
resistance allows the stray capacitance to play a more significant role; i.e., a larger RC time delay is introduced
between the output of the error amplifier and its FEEDBACK input, leading to more phase shift and lower phase
margin. A solution is to add a 100-pF bypass capacitor (C_BYPASS) between OUTPUT and FEEDBACK; because
C_BYPASS is in parallel with R1, it lowers the impedance seen at FEEDBACK at high frequencies, in effect
offsetting the effect of the parasitic capacitance by providing more feedback at higher frequencies. More
feedback forces the error amplifier to work at a lower loop gain, so C_OUT should be increased to a minimum of
3.3 μF to improve the regulator’s phase margin.
C_BYPASS can be also used to reduce output noise in the LP2951-xx-Q1. This bypass capacitor reduces the closed
loop gain of the error amplifier at the high frequency, so noise no longer scales with the output voltage. This
improvement is more noticeable with higher output voltages, because loop gain reduction is greatest. A suitable
C_BYPASS is calculated as shown in Equation 1:
f_(CBYPASS) ] 200 Hz ³ C_BYPASS + _2p
1
R1 200 Hz
(1)
ERROR Function
The LP2951-xx-Q1 has a low-voltage detection comparator that outputs a logic low when the output voltage
drops by ≉6% from its nominal value, and outputs a logic high when V_OUT has reached ≉95% of its nominal
value. This 95% of nominal figure is obtained by dividing the built-in offset of ≉60 mV by the 1.235-V bandgap
reference, and remains independent of the programmed output voltage. For example, the trip-point threshold
(ERROR output goes high) typically is 4.75 V for a 5-V output and 11.4 V for a 12-V output. Typically, there is a
hysteresis of 15 mV between the thresholds for high and low ERROR output.
A timing diagram is shown in Figure 1 for ERROR vs V_OUT (5 V), as V_IN is ramped up and down. ERROR
becomes valid (low) when V_IN ≉ 1.3 V. When V_IN ≉ 5 V, V_OUT = 4.75 V, causing ERROR to go high. Because the
dropout voltage is load dependent, the output trip-point threshold is reached at different values of V_IN, depending
on the load current. For instance, at higher load current, ERROR goes high at a slightly higher value of V_IN, and
vice versa for lower load current. The output-voltage trip point remains at ≉4.75 V, regardless of the load. Note
that when V_IN ≤ 1.3 V, the ERROR comparator output is turned off and pulled high to its pullup voltage. If V_OUT is
used as the pullup voltage, rather than an external 5-V source, ERROR typically is ≉1.2 V. In this condition, an
equal resistor divider (10 kΩ is suitable) can be tied to ERROR to divide down the voltage to a valid logic low
during any fault condition, while still enabling a logic high during normal operation.
14
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: LP2951-33-Q1 LP2951-50-Q1