CC2540T_15 Datasheet, PDF (10/37 Pages) Texas Instruments – SimpleLink CC2540T 2.4-GHz Bluetooth Low Energy Wireless MCU

CC2540T
SWRS172 – JULY 2014
www.ti.com
4.6 General Characteristics
Measured on Texas Instruments CC2540 EM reference design with T_A = 25°C and VDD = 3 V
PARAMETER
TEST CONDITIONS
MIN TYP MAX
WAKE-UP AND TIMING
Power mode 1 → Active
Digital regulator on, 16-MHz RCOSC and 32-MHz crystal
oscillator off. Start-up of 16-MHz RCOSC
4
Power mode 2 or 3 → Active
Digital regulator off, 16-MHz RCOSC and 32-MHz crystal
oscillator off. Start-up of regulator and 16-MHz RCOSC
120
Active → TX or RX
Crystal ESR = 16 Ω. Initially running on 16-MHz RCOSC,
with 32-MHz XOSC OFF
410
With 32-MHz XOSC initially on
160
RX/TX turnaround
150
RADIO PART
RF frequency range
Programmable in 2-MHz steps
2402
2480
Data rate and modulation format
1 Mbps, GFSK, 250 kHz deviation
UNIT
μs
μs
μs
μs
μs
MHz
4.7 RF Receive Section
Measured on Texas Instruments CC2540 EM reference design with T_A = 25°C, VDD = 3 V, f_c = 2440 MHz
1 Mbps, GFSK, 250-kHz deviation, Bluetooth low energy mode, and 0.1% BER⁽¹⁾.
Boldface limits apply over the entire operating range, T_A = –40°C to 125°C, VDD = 2 V to 3.6 V, and f_c = 2402 MHz to 2480
MHz.
PARAMETER
Receiver sensitivity⁽²⁾
Receiver sensitivity⁽²⁾
Saturation ⁽³⁾
Co-channel rejection⁽³⁾
Adjacent-channel rejection⁽³⁾
Alternate-channel rejection⁽³⁾
Blocking ⁽³⁾
Frequency error tolerance⁽⁴⁾
Symbol rate error tolerance⁽⁵⁾
High-gain mode
Standard mode
TEST CONDITIONS
±1 MHz
±2 MHz
Including both initial tolerance and drift
MIN TYP
–93
–87
6
–5
–5
30
–30
–250
–80
MAX
250
80
UNIT
dBm
dBm
dBm
dB
dB
dB
dBm
kHz
ppm
Spurious emission. Only largest spurious
emission stated within each band.
Conducted measurement with a 50-Ω single-ended load.
Complies with EN 300 328, EN 300 440 class 2, FCC CFR47,
Part 15 and ARIB STD-T-66
–75
dBm
Current consumption
RX mode, standard mode, no peripherals active, low MCU
activity, MCU at 250 kHz
RX mode, high-gain mode, no peripherals active, low MCU
activity, MCU at 250 kHz
19.6
mA
22.1 30.5
(1) 0.1% BER maps to 30.8% PER
(2) The receiver sensitivity setting is programmable using a TI BLE stack vendor-specific API command. The default value is standard
mode.
(3) Results based on standard gain mode
(4) Difference between center frequency of the received RF signal and local oscillator frequency
(5) Difference between incoming symbol rate and the internally generated symbol rate
10
Specifications
Submit Documentation Feedback
Product Folder Links: CC2540T
Copyright © 2014, Texas Instruments Incorporated