SN74AUCH32374 Datasheet, PDF (1/11 Pages) Texas Instruments – 32-BIT EDGE-TRIGGERED D-TYPE FLIP-FLOP WITH 3-STATE OUTPUTS

D Member of the Texas Instruments
Widebus+ Family
D Optimized for 1.8-V Operation and is 3.6-V
I/O Tolerant to Support Mixed-Mode Signal
Operation
D I_off Supports Partial-Power-Down Mode
Operation
D Sub 1-V Operable
D Max t_pd of 2.8 ns at 1.8 V
D Low Power Consumption, 40-µA Max I_CC
SN74AUCH32374
32-BIT EDGE-TRIGGERED D-TYPE FLIP-FLOP
WITH 3-STATE OUTPUTS
SCES476 – AUGUST 2003
D ±8-mA Output Drive at 1.8 V
D Bus Hold on Data Inputs Eliminates the
Need for External Pullup/Pulldown
Resistors
D Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
D ESD Protection Exceeds JESD 22
– 2000-V Human-Body Model (A114-A)
– 200-V Machine Model (A115-A)
– 1000-V Charged-Device Model (C101)
description/ordering information
This 32-bit edge-triggered D-type flip-flop is operational at 0.8-V to 2.7-V V_CC, but is designed specifically for
1.65-V to 1.95-V V_CC operation.
The SN74AUCH32374 is particularly suitable for implementing buffer registers, I/O ports, bidirectional bus
drivers, and working registers. It can be used as four 8-bit flip-flops, two 16-bit flip-flops, or one 32-bit flip-flop.
On the positive transition of the clock (CLK) input, the Q outputs of the flip-flop take on the logic levels set up
at the data (D) inputs.
A buffered output-enable (OE) input can be used to place the eight outputs in either a normal logic state (high
or low logic levels) or the high-impedance state. In the high-impedance state, the outputs neither load nor drive
the bus lines significantly. The high-impedance state and increased drive provide the capability to drive bus lines
without interface or pullup components.
OE does not affect internal operations of the latch. Old data can be retained or new data can be entered while
the outputs are in the high-impedance state.
To ensure the high-impedance state during power up or power down, OE should be tied to V_CC through a pullup
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
Active bus-hold circuitry holds unused or undriven inputs at a valid logic state. Use of pullup or pulldown resistors
with the bus-hold circuitry is not recommended.
This device is fully specified for partial-power-down applications using I_off. The I_off circuitry disables the outputs,
preventing damaging current backflow through the device when it is powered down.
ORDERING INFORMATION
TA
PACKAGE†
ORDERABLE
PART NUMBER
TOP-SIDE
MARKING
–40°C to 85°C LFBGA – GKE
Tape and reel SN74AUCH32374GKER MK374
† _{Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines}
are available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Widebus+ is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Copyright  2003, Texas Instruments Incorporated
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265
1