THV3056 Datasheet, PDF(20/32 Page) THine Electronics, Inc. – 3ch Buck/Boost 2ch CP 1ch HVLDO 1ch LVLDO Controller

English

English German Russian Spanish Italian Polish Chinese Japanese Korean French Portuguese	Language :

THV3056 Datasheet, PDF (20/32 Pages) THine Electronics, Inc. – 3ch Buck/Boost 2ch CP 1ch HVLDO 1ch LVLDO Controller

◁

THV3056_Rev.2.00_E

â UVP(Under Voltage Protection)

UVP circuit detects abnormal drops of output voltage caused by short circuits or over load.

The internal UVP comparator monitors the output voltage of error amplifiers(FB1,2,3). In the normal operation the

inverting input voltage is approximately 1.2V, same as the non-inverting input connected internally to VREF. The invert-

ing input voltage decreases in proportion to the output voltage drop. If the output voltage drops below the user defined

voltage, the system goes into Max Duty cycle and UVP comparator reports the abnormal operation of DC/DC converter

to SCP circuit. (See Figure 9)

â Short Circuit Protection ï¼SCP Timer Circuitï¼

SCP shut down the IC operation when the Max Duty operation/OVP operation /abnormal temperature continue for a

longer time than the user defined time. SCP timer circuit has the internal constant source current circuit, a pull-down tran-

sistor and an external capacitor connected between SCP pin and GND. In the normal operation the internal pull-down tran-

sistor is in On state, and SCP pin is held Gnd level. (See Figure 9.)

When UVP comparator detects the output voltage drop, the pull-down transistor connected with SCP pin is turned to Off

and the external capacitor is charged with 1uA constant current. While OVP comparator detects the output voltage rise or

the abnormal temperature is detected continuously, the voltage on SCP pin keep on rising in proportion to the time con-

stant defined by 5uA constant current and the external capacitor. When the voltage on SCP pin reaches to 1.2V, the latch

operates and then all channels stops and goes into shut down mode. (See Figure 10.) The latch state will not be released

until power supply is restarted. The delay time to the latch state can be set by the external capacitance. Also, users can

select SCP timer mode(On/Off) of charge pump by SEL2 pin.(See Table 3.)

The delay time Tscp is given by following :

When Cscp=0.01uF and UVP is activated, the SCP delay time (Tscp) is around 12msec. Also, when OVP or TSD is acti-

vated, Tovp is around 2.4msec.

In the case of UVP,

Tscp

-----1---.---2-----

1ï´10â6

ï´

Cscp=

1.2ï´106 ï´ Cscpï¨ sec

ï©

In the case of OVP or TSD,

Tovp

-----1---.---2-----

5ï´10â6

ï´

2.4ï´105 ï´ Cscpï¨ sec

ï©

Note 1) When output short circuit or over load occur, the input power supply voltage (Vin) may decrease according to the

circumstances. UVLO resets SCP timer latch state, so please set the delay time in order that timer latch works earlier than

UVLO operation. Otherwise, the following operation will be repeated:

Output short-circuit â Power-supply voltage decrease (UVLO operation) â Short-circuit current decrease â Power-sup-

ply voltage rise (UVLO release) â Power-supply voltage decrease

Note 2) When UVP timer latch function of charge pump is set to be enable, please be careful to determine the delay time

considering the startup time of charge pumps. (See Figure 11.)

ããããããããããããããããTable 3 SEL2 pin Settingãã

SEL2 Connection

GND

VREG5

Startup Sequence

C.P Timer Latch/Active

C.P Timer Latch/Inactive

20/32

THine Electronics, Inc.

▷