V23134-F4 Datasheet, PDF (2/4 Pages) TE Connectivity Ltd – Automotive Relays Plug-in Mini ISO Relays

Automotive Relays
Plug-in Mini ISO Relays
Power Relay F4 (Continued)
Max. load DC breaking capacity
6) Without components in parallel.
Insulation Data
Initial dielectric strength
between open contacts
between contact and coil
between adjacent contacts
Load dump test
ISO 7637-1 (12VDC), test pulse 5
ISO 7637-2 (24VDC), test pulse 5
500V_rms
500V_rms
500V_rms
Vs=+86.5VDC
Vs=+200VDC
Other Data
EU RoHS/ELV compliance
compliant
Ambient temperature DC coil
-40 to +125°C
Protection to heat and fire UL94-HB or better⁷⁾
Climatic cycling with condensation
EN ISO 6988 6 cycles, storage 8/16h
Temperature cycling
IEC 60068-2-14, Nb 10 cycles, -40/+85°C (5°C/min)
Load limit curve 1: arc extinguishes during transit time (CO contact).
Damp heat cyclic
Load limit curve 2: safe shutdown, no stationary arc (NO contact).
Load limit curves measured with low inductive resistors verified for 1000 switching events.
IEC 60068-2-30, Db, Variant 1 6 cycles, upper air temp. 55°C
Damp heat constant
IEC 60068-2-3, Ca
56 days
Category of environmental protection,
IEC 61810 RTI – dustproof, RT III – sealed
Degree of protection, IEC 60529 IP54 (dustproof), IP67 (sealed)
Coil Data
Corrosive gas
Rated coil voltage
Coil versions, DC coil
12/24VDC
IEC 60068-2-42 10±2cm³/m³ SO₂, 10 days
IEC 60068-2-43 1±0.3cm³/m³ H₂S, 10 days
Vibration resistance (functional)
Coil
Rated
Operate Release
Coil
Rated coil
IEC 60068-2-6 (sine sweep) 10 to 500Hz > 5g⁸⁾
code
voltage
voltage
voltage resistance⁶⁾ power⁶⁾
Shock resistance (functional)
VDC
VDC
VDC
Ω±10%
W
IEC 60068-2-27 (half sine)
11ms >20g⁸⁾
052
12
7.2
1.6
90
1.6
Drop test, free fall
053
24
14.4
3.2
324
1.8
IEC 60068-2-32 1m onto concrete
056
24
16
4
268
2.1
Terminal type
plug-in, QC/PCB
All figures are given for coil without pre-energization, at ambient temperature +23°C.
Cover retention
Coil operating range
axial force
150N
TE0701-J1
pull force
push force
150N
150N
Terminal retention
pull force
100N
push force
100N
resistance to bending, force applied to front⁹⁾ 10N
resistance to bending, force applied to side⁹⁾ 10N
torque
0.3Nm
Does_PWn_ao^et_cigt_ka^hak^tge _inin_gto_ua_nc_ic_tount
the temp_pe_lr_ua_gtu_-r_ine_/r_Pis_Ce _Bdu e to
the conta_pc_lut _gcu_-r_inre_wnt_{ith bracket}
E = p₇re₎ -_Re_en_fee_rr_sgi_tz_oat_ui_so_en_{d materials.}
approx. 35g (1.2oz)
315 pcs.
200 pcs.
8) No change in the switching state >10μs. Valid for NC contacts, NO contact values
significantly higher.
9) Values apply 2mm from the end of the terminal. When the force is removed, the terminal
must not have moved by more than 0.3mm.
Does not take into account the temperature rise due to the contact current E=pre-
energization..
Accessories
For details see datasheet Connectors for Mini ISO Relays
2
03-2014, Rev. 0314
www.te.com
© 2014 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.