NQ15W50SGA30 Datasheet, PDF (4/11 Pages) SynQor Worldwide Headquarters – SMT Surface Mount

Technical Specification
Input: 6.0 - 15.0V
Outputs: 0.8 - 5.0V
Current: 30A
Package: SMT
ELECTRICAL CHARACTERISTICS (continued) - NQ15W50SGA30 Series
Parameter
Module
TEMP LIMITS FOR POWER DERATING
Semiconductor Junction Temperature
All
Board Temperature
All
FEATURE CHARACTERISTICS
Switching Frequency
All
ON/OFF Control
Negative Logic (N) ON/OFF Control
Off-State Voltage
All
On-State Voltage
All
Pull-Up Voltage
All
Pull-Up Resistance
All
Positive Logic (P) ON/OFF Control
Logic Low Voltage Range
All
Logic High Voltage Range (internal pullup) All
Logic Low Sink Current
All
Logic High Sink Current (leakage)
All
Output Voltage Trim Range
All
Output Over-Voltage Protection
All
Over-Temperature Shutdown
All
Over-Temperature Shutdown Restart Hysteresis All
RELIABILITY CHARACTERISTICS
Calculated MTBF (Telcordia)
All
Calculated MTBF (MIL-217)
All
Field Demonstrated MTBF
All
Min.
330
1.5
-3.0
-0.2
2.2
0.75
5.6
Typ.
360
Max.
125
125
390
6.5
0.6
Vin
49.9
1.0
0.7
10
5.5
6.0
6.4
128
10
14.0
10.8
Units Notes & Conditions
°C Package rated to 150°C
°C UL rated max operating temp 130°C
kHz Half on small duty cycle (e.g. 16Vin; 0.75Vout)
See Figure A
V
V
V
kW
Open collector/drain input; see Figure A
V
V
mA Vin = 15 V
µA
V Measured Vout+ to common pins
V Over full temp range
°C Average PCB Temperature
°C
10⁶ Hrs.
10⁶ Hrs.
TR-NWT-000332; 100% load, 200LFM,
MIL-HDBK-217F; 100% load, 200LFM,
40^oC
40^oC
Ta
Ta
10⁶ Hrs. See our website for details
STANDARDS COMPLIANCE
Parameter P
STANDARDS COMPLIANCE
UL/cUL 60950-1
EN60950-1
72/23/EEC
93/68/EEC
Needle Flame Test (IEC 695-2-2)
IEC 61000-4-2
GR-1089-CORE
Telcordia (Bellcore) GR-513
Notes
File # E194341
Certified by TUV
Test on entire assembly; board & plastic components UL94V-0 compliant
ESD test, 8kV - NP, 15kV air - NP (Normal Performance)
Section 7 - electrical safety, Section 9 - bonding/grounding
• An external input fuse must always be used to meet these safety requirements. Contact SynQor for official safety
certificates on new releases or download from the SynQor website.
QUALIFICATION TESTING
Parameter P
QUALIFICATION TESTING
Life Test
Vibration
Mechanical Shock
Temperature Cycling
Power/Thermal Cycling
Design Marginality
Humidity
Solderability
# Units Test Conditions
32
5
5
10
5
5
5
15 pins
95% rated Vin and load, units at derating point, 1000 hours
10-55Hz sweep, 0.060” total excursion,1 min./sweep, 120 sweeps for 3 axis
100g minimum, 2 drops in x and y axis, 1 drop in z axis
-40°C to 100°C, unit temp. ramp 15°C/min., 500 cycles
Toperating = min to max, Vin = min to max, full load, 100 cycles
Tmin-10°C to Tmax+10°C, 5°C steps, Vin = min to max, 0-105% load
85°C, 85% RH, 1000 hours, continuous Vin applied except 5min./day
MIL-STD-883, method 2003
• Extensive characterization testing of all SynQor products and manufacturing processes is performed to ensure that we supply
robust, reliable product. Contact the factory for official product family qualification documents.
Product # NQ15W50SGA30
Phone [phone]
www.synqor.com
Doc.# 005-2NS163E Rev. C
10/03/08
Page 4