PQ60120QEA17 Datasheet, PDF (3/14 Pages) SynQor Worldwide Headquarters – Quarter-brick DC-DC Converter

Technical Specification
Input: 35-75 V
Output: 12 V
Current: 17 A (200W)
Package: Quarter-brick
MECHANICAL DIAGRAM (base-plated)
2.30
(58.4)
0.14
(3.6)
2.00
(50.8)
Top View
0.43
(10.9)
1
2
3
0.600
(15.24)
0.300
(7.62)
M3 Threaded Inserts
4 Places
See Notes 11 & 12
1.86
(47.2)
8
7
6
5
4
0.22
(5.6)
0.600
(15.24)
0.450
(11.43)
0.300
(7.62)
0.150
(3.81)
0.21
(5.3)
1.03
(26.2)
1.45
(36.8)
Side View
0.499 max
(12.67)
Bottom side
Clearance
See Note 9
0.025 +.024
(10.46 +0.60)
Lowest
Component
Flanged Pin
Load Board See Note 10
0.180
(4.57)
See Note 3
NOTES
PIN DESIGNATIONS
1) Pins 1-3, 5-7 are 0.040” (1.02mm) diameter with 0.080”
(2.03 mm) diameter standoff shoulders.
2) Pins 4 and 8 are 0.062” (1.57 mm) diameter with 0.100”
(2.54 mm) diameter standoff shoulders.
3)Other pin extension lengths available.Recommended pin length is
0.03” (0.76mm) greater than the PCB thickness.
PIN NAME
1 Vin(+)
2 ON/OFF
FUNCTION
Positive input voltage
TTL input to turn converter on
and off, referenced to Vin(–),
with internal pull up.
4) All Pins: Material - Copper Alloy
Finish (RoHS 5/6) - Tin/Lead over Nickel plate
Finish (RoHS 6/6) - Matte Tin over Nickel plate
5) Undimensioned components are shown for visual reference only.
6) All dimensions in inches (mm)
Tolerances: x.xx+0.02 in. (x.x+0.5mm)
x.xxx+0.010 in. (x.xx+0.25mm)
7) Weight: 2.4 oz. (69 g) typical
3 Vin(–) Negative input voltage
4 Vout(–) Negative output voltage
5 SENSE(–) Negative remote sense1
6 TRIM
Output voltage trim2
7 SENSE(+) Positive remote sense3
8 Vout(+) Positive remote sense3
8) Workmanship: Meets or exceeds IPC-A-610C Class II
Notes:
9)UL/TUV standards require a clearance greater than 0.04” (1.02mm) between input _{1. SENSE(–) should be connected to Vout(–) either}
and output for Basic insulation. This issue should be considered if any copper traces
remotely or at the converter.
are on the top side of the user’s board. Note that the ferrite cores are considered
part of the input/primary circuit.
2. Leave TRIM pin open for nominal output voltage.
10) The flanged pins are designed to permit surface mount soldering (avoiding the
wave soldering process) through the use of the flanged pin-in-paste technique.
3. SENSE(+) should be connected to Vout(+) either
remotely or at the converter.
11) M3 screws used to bolt unit’s baseplate to other surfaces such as a heatsink must
not exceed 0.100” (2.54mm) depth below the baseplate surface.
12) Applied torque per screw should not exceed 6 in-lb (0.7 Nm).
Product # PQ60120QEA17
Phone [phone]
www.synqor.com
Doc.# 005-0005068 Rev. A
03/19/09
Page 3