PQ60120QZB33 Datasheet, PDF (2/13 Pages) SynQor Worldwide Headquarters – Protection from permanent damage and hazardous conditions

Baseplated Mechanical Diagram
1.45 [36.7]
1.03 [26.2]
.600 [15.24]
.450 [11.43]
.300 [7.62]
.150 [3.81]
2.30
[58.4]
1.86
[47.2]
2.00
[50.8]
87 6 5 4
TOP VIEW
.43 [10.8]
.300 [7.62]
.600 [15.24]
12 3
.21
[5.3]
.22
[5.6]
M3 THREADED INSERTS
4 PLACES
SEE NOTES 1 & 2
.14 [3.6]
Technical
Specification
PQ60120QZB33
.180
[4.57]
SEE NOTE 6
SIDE VIEW
030 ±.024
[0.76 ±0.6]
BOTTOMSIDE
CLEARANCE
.496 ±.014
[12.6 ±0.35]
OVERALL HEIGHT (RSS)
NOTES
1) M3 screws used to bolt unit’s baseplate to other surfaces (such as a
heatsink) must not exceed 0.100” (2.54 mm) depth below the surface
of the baseplate.
2) Applied torque per screw should not exceed 6in-lb. (0.7 Nm).
3) Baseplate flatness tolerance is 0.004” (.10mm) TIR for surface.
4) Pins 1-3, 5-7 are 0.040” (1.02mm) diameter, with 0.080” (2.03mm)
diameter standoff shoulders.
5) Pins 4 and 8 are 0.062” (1.57 mm) diameter with 0.100” (2.54 mm)
diameter standoff shoulders.
6) Other pin extension lengths available. Recommended pin length is
0.03” (0.76mm) greater than the PCB thickness.
7) All Pins: Material - Copper Alloy- Finish - Matte Tin over Nickel plate
8) Undimensioned components are shown for visual reference only.
9) All dimensions in inches (mm) Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm)
x.xxx +/-0.010 in. (x.xx +/-0.25mm)
10) Weight: 2.4 oz. (69 g) typical
11) Workmanship: Meets or exceeds IPC-A-610C Class II
12) UL/TUV standards require a clearance greater than 0.04” (1.02mm)
between input and output for Basic insulation. This issue should be
considered if any copper traces are on the top side of the user’s board.
Note that the ferrite cores are considered part of the input/primary circuit
PIN DESIGNATIONS
Pin Name Function
1
Vin(+) Positive input voltage
2
ON/OFF
TTL input to turn converter on and off,
referenced to Vin(–), with internal pull up.
3
Vin(–) Negative input voltage
4
Vout(–) Negative output voltage
5 SENSE(–) Negative remote sense (See note 1)
6
TRIM
Output voltage trim (See note 2)
7 SENSE(+) Positive remote sense (See note 3)
8
Vout(+) Positive output voltage
Notes:
1) SENSE(–) should be connected to Vout(–) either remotely or at the converter.
2) Leave TRIM pin open for nominal output voltage.
3) SENSE(+) should be connected to Vout(+) either remotely or at the converter.
Product # PQ60120QZB33
Phone [phone]
www.synqor.com
Doc.# 005-0005586 Rev. G
02/04/15
Page 2