PQ60050QTA30 Datasheet, PDF (1/13 Pages) SynQor Worldwide Headquarters – Quarter-brick DC/DC Converter

Technical
Specification
PQ60050QTA30
48Vin 5.0Vout
Input
Output
30Amp
Current
2000Vdc
Isolation
Quarter-brick
DC/DC Converter
The PQ60050QTA30 PowerQor^® Tera quarter-brick
converter is a next-generation, board-mountable,
isolated, fixed switching frequency DC/DC converter
that uses synchronous rectification to achieve
extremely high conversion efficiency. The power
dissipated by the converter is so low that a heatsink
is not required, which saves cost, weight, height,
and application effort. All of the power and control
components are mounted to the multi-layer PCB
substrate with high-yield surface mount technology.
Since the PowerQor converter has no explicit thermal
interfaces, it is extremely reliable. The Tera series
offers the maximum useable output current for any
standard “quarter-brick” module. RoHS compliant
(see page 13).
PQ60050QTA30 Module
Operational Features
• Ultra-high efficiency, >90% at full rated load current
• Delivers up to 30 amps of output current (150W) with
minimal derating - no heatsink required
• Wide input voltage range: 35 – 75V, with 100V 100ms
input voltage transient capability
• Fixed frequency switching provides predictable EMI
performance
• No minimum load requirement means no preload
resistors required
Mechanical Features
• Industry standard quarter-brick pin-out configuration
• Industry standard size: 1.45” x 2.3” (36.8x58.4mm)
• Total height less than 0.43” (10.9mm), permits better
airflow and smaller card pitch
• Total weight: 1.5 oz. (42 grams)
• Flanged pins designed to permit surface mount
soldering (avoid wave solder) using FPiP technique
Protection Features
• Input under-voltage lockout disables converter at low
input voltage conditions
• Output current limit and short circuit protection
protects converter and load from permanent damage
and consequent hazardous conditions
• Active back bias limit prevents damage to converter
from external load induced pre-bias
• Output over-voltage protection protects load from
damaging voltages
• Thermal shutdown protects converter from abnormal
environmental conditions
Safety Features
• 2000 V, 30MΩ input-to-output isolation
• UL 60950-1:2003, basic insulation
• CAN/CSA-C22.2 No. 60950-1:2003
• EN60950-1:2001
• RoHS compliant (see page 13)
Control Features
Contents
• On/Off control referenced to input side (positive and
negative logic options are available)
• Remote sense for the output voltage compensates for
output distribution drops
• Output voltage trim permits custom voltages and
voltage margining
Page No.
Mechanical Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
PQ60050QTD30 ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . 3-
STANDARDS COMPLIANCE & QUALIFICATION TESTING . . . . . . . . . . . . . 4
Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Application section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-12
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Product # PQ60050QTA30
Phone [phone]
www.synqor.com
Doc.# 005-2QT650C Rev. E
05/20/09
Page 1