M24C04-DRE Datasheet, PDF (29/41 Pages) STMicroelectronics – 4-Kbit serial IC bus EEPROM - 105C operation

M24C04-DRE
DC and AC parameters
Table 10. DC characteristics
Symbol
Parameter
Test conditions (in addition to
those in Table 6 and Table 7)
Min.
Max. Unit
I_LI
Input leakage current
(SCL, SDA, E_i)
V_IN = V_SS or V_CC,
device in Standby mode
-
±2
µA
I_LO Output leakage current
SDA in Hi-Z, external voltage
applied on SDA: V_SS or V_CC
-
±2
µA
f_C = 400 kHz, V_CC = 5.5 V
-
2
mA
f_C = 400 kHz, V_CC = 2.5 V
-
2
mA
I_CC Supply current (Read)
f_C = 400 kHz, V_CC = 1.8 V
f_C = 1 MHz, V_CC = 5.5 V
-
1
mA
-
2
mA
f_C = 1 MHz, V_CC = 2.5 V
-
2
mA
f_C = 1 MHz, V_CC = 1.8 V
-
2
mA
I_CC0 Supply current (Write)
During t_W
-
2
mA
Device not selected⁽¹⁾⁽²⁾, t° = 85
°C, V_IN = V_SS or V_CC, V_CC = 1.8 V
-
1
Device not selected⁽¹⁾⁽²⁾, t° = 85
°C, V_IN = V_SS or V_CC, V_CC = 2.5 V
-
2
I_CC1 Standby supply current
Device not selected⁽¹⁾⁽²⁾, t° = 85
°C, V_IN = V_SS or V_CC, V_CC = 5.5 V
-
Device not selected⁽¹⁾, t° = 105 °C,
V_IN = V_SS or V_CC, V_CC = 1.8 V
-
3
µA
5
Device not selected⁽¹⁾, t° = 105 °C
V_IN = V_SS or V_CC, V_CC = 2.5 V
-
5
Device not selected⁽¹⁾, t° = 105 °C,
V_IN = V_SS or V_CC, V_CC = 5.5 V
-
10
V_IL Input low voltage (SCL, SDA, WC, E_i)⁽³⁾ -
–0.45 0.3 V_CC V
Input high voltage (SCL, SDA)
-
V_IH
Input high voltage (WC, E_i)⁽⁴⁾
-
0.7 V_CC 6.5
V
0.7 V_CC V_CC +0.6 V
V_OL Output low voltage
V_RES ⁽²⁾ Internal reset threshold voltage
I_OL = 2.1 mA, V_CC = 2.5 V or
I_OL = 3 mA, V_CC = 5.5 V
I_OL = 1 mA, V_CC = 1.8 V
-
-
0.4
V
-
0.3
V
0.5
1.5
V
1. The device is not selected after power-up, after a Read instruction (after the Stop condition), or after the
completion of the internal write cycle t_W (t_W is triggered by the correct decoding of a Write instruction).
2. Characterized only, not 100% tested.
3. Ei inputs should be tied to Vss (see Section 2.3).
4. Ei inputs should be tied to V_CC (see Section 2.3).
DocID027421 Rev 1
29/41