CY28159 Datasheet, PDF (2/12 Pages) Cypress Semiconductor – Clock Generator for Serverworks Grand Champion Chipset Applications

CY28159
Pin Description
Pin
20
Name
SSCG
7,10, 13, 16,
42, 39, 36, 33
8, 11, 14, 17,
41, 38, 35, 32
26
CPU(0:7)
CPU(0:7)#
IRef
1
3V33
44
PD#
3, 4
48
23
22
19
30, 29
48M(0,1), S(0,1)
SEL100/133
XOUT
XIN
REF
Mult(0,1)
25, 46
2, 6, 12, 18, 24,
31, 37, 43
5, 9, 15, 21, 28,
34, 40, 47
27, 45
VDDA
VDD
VSS
VSSA
I/O^[1]
PU
I
O
P
O
PU
I
IO
PU
I
O
I
O
I
P
P
Description
When asserted LOW, this pin invokes Spread Spectrum functionality. Spread
spectrum is applicable to CPU(0:7), CPU(0:7)#. This pin has a 250-k: internal
pull-up.
Differential host clock outputs. These outputs are used in pairs, (CPU0-0#,
CPU1-1#, CPU2-2#, CPU3-3#, CPU4-4#, CPU5-5#, CPU6-6#, and CPU7-7#)
for differential clocking of the host bus. CPU(0:7) are 180 degrees out of phase
with their complements, CPU(0:7)#. See Table 1 on page 1
This pin establishes the reference current for the internal current steering
buffers of the CPU clocks. A resistor is connected from this pin to ground to set
the value of this current.
Fixed 33.3-MHz clock output.
When asserted LOW, this pin invokes a power-down mode by shutting off all
the clocks, disabling all internal circuitry, and shutting down the crystal oscil-
lator. The 48M(0:1) and REF clocks are driven LOW during this condition and
the CPU clocks are driven HIGH and programmed with an 2X IREF current. It
has a 250-k: internal pull-up.
S0 and S1 inputs are sensed on power-up and then internally latched. After-
wards the pins are 3V 48-MHz clocks.
Input select pin. See Table 1 on page 1.
It has a 250-k: internal Pull-up
Crystal Buffer output pin. Connects to a crystal only. When an external signal
other than a crystal is used or when in Test mode, this pin is kept unconnected.
Crystal Buffer input pin. Connects to a crystal, or an external single ended input
clock signal.
A buffered output clock of the signal applied at Xin. Typically, 14.31818 MHz.
These input select pins configure the Ioh current (and thus the Voh swing
amplitude) of the CPU clock output pairs. Each pin has a 250-k: internal
Pull-up. See Table 6 for current and resistor values.
3.3V power supply pins.
3.3V power supply pins for common supply to the core.
P Ground pins for common supply to the core.
P Ground pins.
Note:
1. Definition of I/O column mnemonic on pin description table above 1= Input pin, O = output pin, P = power supply pin, PU = indicates that a bidirectional pin contains
pull-up resistor. This will insure that this pin of the device will be seen by the internal logic as a logic 1 level. Likewise pins with a PD designation are guaranteed
to be seen as a logic 0 level if no external level setting circuitry is present at power up.
Rev 1.0, November 24, 2006
Page 2 of 12