English
Language : 

AAT3673 Datasheet, PDF (22/28 Pages) Skyworks Solutions Inc. – 1.6A Dynamic Battery Charger and Power Manager
DATA SHEET
AAT3673
1.6A Dynamic Battery Charger and Power Manager
Status Indicator Display
Simple system charging status states can be displayed
using one LED each in conjunction with the STAT1 and
STAT2 pins of the AAT3673-1/-2/-4/-5 and the STAT1
pin of the AAT3673-3/-6. These pins have simple switch-
es connecting the LED’s cathodes to ground. Refer to
Tables 6, 7, and 8 for LED display definitions. The LED
anodes should be connected to BYP or other system
power that does not exceed 6.5V, depending upon sys-
tem design requirements. The LED should be biased with
as little current as necessary to create reasonable illumi-
nation; therefore, a ballast resistor should be placed
between the LED cathode and the STAT1 and STAT2 pins
of the AAT3673-1/-2/-4/-5 and the STAT1 pin of the
AAT3673-3/-6. A 2mA bias current should be sufficient
to drive most low cost green or red LEDs. It is not rec-
ommended to exceed 8mA when driving an individual
status LED.
The required ballast resistor value can be estimated
using the following formulas:
When connecting to the adapter supply with a red LED:
RB(STAT1,2) =
VADP - VFLED
ILED(STAT1,2)
Example:
RB(STAT1,2) =
5.5V - 2.0V
2mA
= 1.75kΩ
Red LED forward voltage (VF) is typically 2.0V @ 2mA.
When connecting to the USB supply with a green LED:
RB(STAT1,2) =
VUSB - VFLED
ILED(STAT1,2)
Example:
RB(STAT1,2) =
5.0V - 3.2V
2mA
= 900Ω
Green LED forward voltage (VF) is typically 3.2V @ 2mA.
Protection Circuitry
Thermal Loop Control
Due to the integrated nature of the linear charging con-
trol pass devices for both the adapter and USB modes,
a special thermal loop control system has been employed
to maximize charging current under all operating condi-
tions.
The thermal management system measures the internal
circuit die temperature and reduces the charge current
when the device exceeds a preset internal temperature
control threshold. Once the thermal loop control becomes
active, the constant charge current is initially reduced by
a factor of 0.44.
The initial thermal loop current can be estimated by the
following equation:
Constant Charging: ITLOOP = ICCADP · 0.44
The thermal loop control re-evaluates the internal die
temperature every three seconds and adjusts the fast
charge current back up in small steps up to the full fast
charge current level or until an equilibrium current is
discovered and maximized for the given ambient tem-
perature condition. In this manner, the thermal loop
controls the system charge level. The AAT3673 will
always provide the highest possible level of constant
current in the fast charge mode for any given ambient
temperature condition.
Programmable Watchdog Timer
The AAT3673 contains a watchdog timing circuit which
operates in all charging modes. Typically a 0.1μF ceram-
ic capacitor is connected between the CT pin and ground.
When a 0.1μF ceramic capacitor is used, the device will
time a shutdown condition if the trickle charge mode
exceeds 50 minutes. When the device transitions from
the trickle charge to the fast charge constant current
mode and then to the constant voltage mode, the timer
counting is continuous but the timeout value changes
from 50 minutes to 7 hours.
Summary for a 0.1μF used for the timing capacitor:
Trickle Charge (TC) time out = 50 minutes
Trickle Charge (TC) + Fast Charge Constant Current (CC)
+ Constant Voltage (CV) mode time out = 7 hours
The CT pin is driven by a constant current source and
will provide a linear response to increases in the timing
capacitor value. Thus, if the timing capacitor were to be
doubled from the nominal 0.1μF value, the time out time
of the CC + CV modes would be doubled. The corre-
sponding trickle charge time out time would be the com-
bined CC + CV time divided by 8.
If the programmable watchdog timer function is not
needed it may be disabled by terminating the CT pin to
ground. The CT pin should not be left floating or not
terminated; this will cause errors in the internal timing
control circuit.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
22
201881B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • April 25, 2012