SP690SEN-L Datasheet, PDF (2/20 Pages) Sipex Corporation – 3.0V/3.3V Low Power Microprocessor Supervisory with Battery Switch-Over

ABSOLUTE MAXIMUM RATINGS
These are stress ratings only and functional operation of the device at
these ratings or any other above those indicated in the operation
sections of the specifications below is not implied. Exposure to absolute
maximum rating conditions for extended periods of time may affect
reliability and cause permanent damage to the device.
V ..................................................................................-0.3V to 6.0V
CC
V ................................................................................-0.3V to 6.0V
BATT
All Other Inputs (NOTE 1).................................-0.3V to the higher of V_CC or V_BATT
Continuous Input Current:
V ..................................................................................100mA
CC
V_BATT..................................................................................20mA
GND..................................................................................20mA
WDI, PFI...........................................................................20mA
Continuous Output Current:
RESET, RESET, PFO.........................................................20mA
V_OUT......................................................................................100mA
Power Dissipation per Package:
8pin NSOIC (derate 6.14mW/°C above +70°C)..............500mW
8pin PDIP (derate 11.8mW/°C above +70°C)..............1,000mW
Storage Temperature........................................-65°C to +160°C
Lead Temperature(soldering,10sec).............................................+300°C
ESD Rating........................................................4KV Human Body Model
SPECIFICATIONS
V = 3.17V to 5.50V for the SP690T/SP80_T, V = 3.02V to 5.50V for the SP690S/SP80_S, V = 2.72V to 5.50V for the SP690R/SP80_R, V = 3.60V, and
CC
CC
CC
BATT
T = T to T unless otherwise noted. Typical values taken at T = +25^OC.
A
MIN
MAX
AMB
PARAMETERS
Operating Voltage Range,
MIN.
1.0
TYP.
MAX. UNITS CONDITIONS
5.5 Volts
V_CC or V_BATTERY, NOTE 1
V_CC Supply Current, I_SUPPLY
V_CC Supply Current in Battery
Backup Mode
25
40
20
40
V_BATTERY Supply Current in
Any Mode, NOTE 2
0.4
1
V
Leakage Current, NOTE 3
BATTERY
0.001
0.5
V_BATTERY Leakage Current, NOTE 4
-0.1
0.02
Output Voltage, V
OUT
V_OUT in Battery-Backup Mode
Battery Switch Threshold,
V_CC falling
Battery Switch Threshold,
V_CC rising, NOTE 7
V - 0.03
CC
V_CC - 0.3
V_CC - 0.0015
V - 0.0075
CC
V_CC - 0.075
V_CC - 0.0003
V_BATTERY - 0.02
V_BATTERY - 0.0045
V_BATTERY - 0.018
V_BATTERY - 0.15
0.065
0.025
2.30
2.40
2.50
µA excluding I_OUT
µA
V_CC=2.0V,V_BATTERY=2.3V,
excluding I_OUT
µA excluding I_OUT
µA
µA 3.3V > V_CC >V_BATTERY + 0.2V
I = 5mA
V
I_OUT = 50mA
I_OUT = 250µA, V_CC > 2.5V
V
I_OUT = 250µA, V_BATTERY = 2.3V
I_OUT = 1mA, V_BATTERY = 2.3V
I_OUT = 10mA, VB_ATTERY = 3.3V
V
V_BATTERY - V_CC, V_SW > V_CC > 1.75V, NOTE 5
V_BATTERY > V_CC, NOTE 6
Values are identical to the Reset
V
Threshold values at V_CC rising
SP690T/S/R JAN 30-06 SP690T/S/R, 802/T/S/R, 804T/S/R, 805T/S/R Low Power Microprocessor Supervisory
2
© 2006 Sipex Corporation