SGS4-S076P3PS1T00 Datasheet, PDF (7/9 Pages) SICK AG – SWITCHING AUTOMATION LIGHT GRIDS

SGS4-S076P3PS1T00 | SLG
SWITCHING AUTOMATION LIGHT GRIDS
If the teach button is pressed longer than 5 s, you switch into the configuration mode. In the configuration mode the menu items
are indicated by the green LEDs. If the teach button is then pressed for < 1 s, the respective function is activated or reset (yellow
LED on or off). If the teach button is pressed for 1 s to 5 s long, you switch to the next menu item. To exit the configuration mode,
press the teach button for > 5 s or wait for 30 s.
1. Light grid in RUN mode,
green LED “ON”
illuminates, yellow LED
“Q” illuminates.
1
2
3
ON
Q
Func
>5s
2. Cross or parallel beam
set up. ¹⁾
1
1
2
2
3 ^<1s
3
ON
ON
Q
Q
1
2
3. Go to the next menu item. 4. Exit the configuration
mode.
1 s ... 5 s
3
1
2
3
ON
Q
>5s
oder
4
1
2
> 30 s 3
ON
Q
Press teach button > 5 s.
The light grid switches into the
configuration mode – menu item
“cross beam/parallel beam”.
The first green LED from top
flashes.
1 = Yellow LED on,
“Crossed beam” active.
2 = Yellow LED off,
“Parallel beam” active.
Press teach button < 1 s to
switch between the settings.
Press teach button for 1 s to 5 s
to switch to the next menu item
(in this case “alignment aid”).
3 = Press teach button > 5 s,
save parameters.
4 = Wait > 30 s,
parameters not saved.
1) _{Configure the light grid in a 3-way cross-beam or a parallel-oriented operating principle. The cross beam can be used to improve the resolution in the middle detection area. Objects up to a size}
of 25 mm can be detected. The response time increases.
The other menu items in sequence of the menu setting of the light grid
Alignment aid ²⁾
active
1
2
3
ON
Q
inactive
1
2
3
ON
Q
Invert switching
output
Q1
1
2
3
ON
Q
Q
Q1
1
2
3
ON
Q
Q
Auto-teach ³⁾
active
1
2
AUTO
TEACH
3
ON
Q
inactive
1
2
AUTO
3
TEACH
ON
Q
Pushbutton lock Standard values ⁴⁾ Invert second
switching output
Muting ⁵⁾
active
active
Q2
active
1
1
1
1
2
2
2
2
3
3
3
3
ON
ON
ON
MUTING
ON
Q
Q
Q2
Q
Q
inactive
inactive
1
2
3
ON
Q
Q2
1
2
3
ON
Q
Q2
inactive
1
1
2
2
3
3
ON
MUTING
ON
Q
Q
2) _{The alignment aid is recommended for applications with high ranges. The signal strength of the receiver is permanently displayed by four green alignment LEDs. Depending on the strength,}
the number of illuminated LEDs differ. When reception is strong, all four LEDs illuminate. The alignment aid must be deactivated again after alignment.
3) _{After commissioning (power on), the switching threshold is taught in automatically. No object should be between the sender and receiver during this process.}
4) _{With standard values “active” all parameters are reset to the delivery state.}
5) _{If a beam is interrupted permanently, it disappears after > 60 s, and the switching output Q1 is enabled again. If a second switching output is present, it remains inactive.}
2016-03-09 17:40:10 | Online data sheet
S ubject to change without notice
AUTOMATION LIGHT GRIDS | SICK
7