SGM3145 Datasheet, PDF (9/12 Pages) SG Micro Corp – 8-Channel PWM Dimming Charge Pump White LED Driver

SGM3145
APPLICATION INFORMATION
The SGM3145 uses a fractional switched capacitor
charge pump to power up to 8 white LEDs with a
programmable current for uniform intensity. The part
integrates current sources and automatic mode selection
charge pump. It maintains the high efficiency by utilizing
a 1×/1.5× fractional charge pump and current sources.
The small equivalent 1× mode open loop resistance and
ultra-low dropout voltage of current source extend the
operating time of 1× mode and optimize the efficiency in
white LED applications.
Input UVLO
The input operating voltage range of the SGM3145 is
2.7V to 5.5V. An input capacitor at the VIN pin could
reduce ripple voltage. It is recommended to use a
ceramic 1μF or larger capacitance as the input capacitor.
This IC provides an under-voltage lockout (UVLO)
function to prevent it from unstable issue when startup.
The UVLO threshold of input rising voltage is set at 2.15V
typically with a hysteresis 30mV.
Soft-Start
The SGM3145 employs a soft-start feature to limit the
inrush current. The soft-start circuit prevents the
excessive inrush current and input voltage droop. The
soft-start clamps the input current over a typical period of
150μs.
Mode Decision
The SGM3145 uses a smart mode selection method to
decide the working mode for optimizing the efficiency.
Mode decision circuit senses the output and LED voltage
for up/down selection. The SGM3145 automatically
switches to 1.5× mode whenever the dropout condition is
detected from the current source and returns to 1× mode
whenever the dropout condition releases.
Chip Enable and Shutdown
When EN is in “High” status, SGM3145 will enter into
active status. When EN is in “Low” status and SGM3145
will enter into shutdown status.
Over-Voltage Protection
The SGM3145 equips over-voltage protection function.
When LED1 is open, the output voltage will be clamped
to 5.4V.
SG Micro Corp
www.sg-micro.com
8-Channel PWM Dimming
Charge Pump White LED Driver
LED Connection
The SGM3145 supports up to 8 white LEDs. The 8 LEDs
are connected from VOUT to pin 1, 2, 3, 4, 5, 6, 7 and 8
respectively. Figure 1 shows the connection for 8-WLEDs
application. LED1 to LED8 are controlled by EN pin. The
SGM3145 internal current source reference circuit bases
feedback from current sensed on the LED1 output. For
best operation, the only requirement for this type of
application is the output LED1 should always be
connected to the load circuit. The other LED pins (LED2,
3, 4, 5 …) can be left floating if those white LEDs are not
used.
LED Dimming Control Interface
An internal resistor sets the maximum LED current to be
27mA. One PWM signal at PWM pin can dim the
brightness of LED from 0mA to 27mA. When duty cycle =
0%, the current is 0mA; when duty cycle = 100%, the
current is 27mA.
Selecting Capacitors
To get the better performance of SGM3145, the selection
of peripherally appropriate capacitor and value is very
important. These capacitors determine some parameters
such as input/output ripple voltage, power efficiency, and
maximum supply current by charge pump. To reduce the
input and output ripple effectively, the low ESR ceramic
capacitors are recommended. For LED driver
applications, the input voltage ripple is more important
than output ripple. Input ripple is controlled by input
capacitor C_IN, increasing the value of input capacitance
can further reduce the ripple. Practically, the input
voltage ripple depends on the power supply impedance.
The flying capacitor C1 and C2 determine the supply
current capability of the charge pump and to influence the
overall efficiency of system. The lower value will improve
efficiency, but it will limit the LED's current at low input
voltage. For 8 × 27mA load over the entire input range of
2.7V to 5.5V, it is recommended to use a 1μF ceramic
capacitor on the flying capacitor C1 and C2.
9