LC895196 Datasheet, PDF (2/12 Pages) Sanyo Semicon Device – ATA-PI Compatible CD-ROM Decoder IC

LC895196
Allowable Operating Ranges at Ta = –30 to +70°C, V_SS = 0 V
Parameter
Supply voltage
Input voltage range
Symbol
V_DD
V_IN
Conditions
min
4.5
0
Ratings
typ
5.0
Unit
max
5.5
V
V_DD
V
DC Characteristics at V_SS = 0 V, V_DD = 4.5 to 5.5 V, Ta = –30 to +70°C
Parameter
Input high level voltage
Input low level input
Input high level voltage
Input low level input
Input high level voltage
Input low level input
Output high level voltage
Output low level voltage
Output high level voltage
Output: Low level voltage
Output high level voltage
Output low level voltage
Output low level voltage
Output low level voltage
Input leakage current
Output leakage current
Pull-up resistor
Symbol
V_IH1
V_IL1
V_IH2
V_IL2
V_IH3
V_IL3
V_OH1
V_OL1
V_OH2
V_OL2
V_OH3
V_OL3
V_OL4
V_OL5
I_IL
I_OZ
R_UP
Conditions
Applicable pins (see below)
TTL compatible (1)
min
2.2
TTL compatible with pull-up resistor: (10)
2.2
TTL compatible Schmitt: (2), (3), (11)
2.4
I_OH = –2 mA: (4), (10)
V_DD – 2.1
I_OL = 2 mA: (4), (10)
I_OH = –8 mA: (5)
V_DD – 2.1
I_OL = 8 mA: (5)
I_OH = –4 mA: (8), (11)
V_DD – 2.1
I_OL = 24 mA: (8), (11)
I_OL = 2 mA: (9)
I_OL = 8 mA: (6), (7)
V_I = V_SS, V_DD: (1), (2), (3), (11)
–10
When high impedance output: (6), (8), (9), (11)
–10
(7), (10)
40
Ratings
typ
80
Note: The applicable pins correspond to the following names.
[INPUT]
(1) ..........ATPINSEL, CSCTRL, SUA0 to SUA6, BCK, C2PO, LRCK, SDATA, SBSO, SCOR, WFCK, TEST0, TEST1
(2) ..........ZRESET, ZCS, ZRD, ZWR, CSEL
(3) ..........DA0 to DA2, ZCS1FX, ZCS3FX, ZDIOR, ZDIOW, ZDMACK, ZHRST
[OUTPUT]
(4) ..........RA0 to RA9, ZCAS0, ZCAS1, ZLWE, ZOE, ZRAS0, ZRAS1, ZUWE, DBCK, DLRCK, DSDATA, EXCK
(5) ..........MCK, MCK2, MCK3
(6) ..........ZRSTCPU, ZRSTIC
(7) ..........ZINT, ZINT1, ZSWAIT
(8) ..........DMARQ, HINTRQ
(9) ..........IORDY, ZIOCS16
[INPUT]
(10) ..........D0 to D7, IO0 to IO15
(11) ..........DD0 to DD15, ZDASP, ZPDIAG
* The XTAL0, XTALCK0, XTAL1, XTALCK1 pins are not included in the CD characteristics.
Unit
max
V
0.8
V
V
0.8
V
V
0.8
V
V
0.4
V
V
0.4
V
V
0.4
V
0.4
V
0.4
V
+10
µA
+10
µA
160
kΩ
Recommended Example of Oscillator Circuit
R1 = 1 MΩ
R2 = 47 Ω
C1 = 0
C2 = 47 pF
Ceramic oscillator frequency = 33.8688 MHz.
The 33.8688 MHz recommended example is for a 3× overtone.
R1 = 1 MΩ
R2 = 15 Ω
C1 = 0
C2 = 15 pF
Ceramic oscillator frequency (XTALCK0) = 50 MHz
Because the specific values are influenced by the circuit board,
confer with the oscillator manufacturer.
No. 5737-2/12