LB11697V Datasheet, PDF (2/14 Pages) Sanyo Semicon Device – Monolithic Digital IC Brushless Motor Driver IC

LB11697V
Specifications
Absolute Maximum Ratings at Ta = 25°C
Parameter
Symbol
Conditions
Supply voltage 1
Output current
LVS pin applied voltage
V_CC max
I_O max
LVS max
V_CC pin
UL, VL, WL, UH, VH, and WH pins
LVS pin
Allowable power dissipation 1
Pd max1 Independent IC
Allowable power dissipation 2
Pd max2 Circuit board*
Operating temperature
Topr
Storage temperature
Tstg
* When mounted on a 114.3 × 76.1 × 1.6 mm glass epoxy board
Ratings
Unit
18
V
30
mA
18
V
0.45
W
1.05
W
–20 to +100
°C
–55 to +150
°C
Allowable Operating Ranges at Ta = 25°C
Parameter
Supply voltage range 1-1
Supply voltage range 1-2
Output current
5 V constant voltage output current
HP pin applied voltage
HP pin output current
RD pin applied voltage
RD pin output current
Symbol
V_CC1-1
V_CC1-2
I_O
IREG
VHP
IHP
VRD
IRD
Conditions
V_CC pin
V_CC pin, when V_CC is shorted to VREG.
UL, VL, WL, UH, VH, and WH pins
Ratings
Unit
8 to 17
V
4.5 to 5.5
V
25
mA
–30
mA
0 to 17
V
0 to 15
mA
0 to 17
V
0 to 15
mA
Electrical Characteristics at Ta = 25°C, V_CC = 12 V
Parameter
Current drain 1
Current drain 2
5 V Constant Voltage Output (VREG pin)
Output voltage
Line regulation
Load regulation
Temperature coefficient
Output Block
Output voltage 1-1
Output voltage 1-2
Output voltage 2
Output voltage 3
Output leakage current
Hall Amplifier Block
Input bias current
Common-mode input voltage range 1
Common-mode input voltage range 2
Symbol
I_CC1
I_CC2
Stop mode
Conditions
VREG
∆VREG1
∆VREG2
∆VREG3
V_CC = 8 to 17 V
I_O = –5 to –20 mA
Design target value*
Ratings
Unit
min
typ
max
12
16 mA
2.5
4 mA
4.7
5.0
5.3
V
40
100 mV
5
30 mV
0
mV/°C
V_OUT1-1
V_OUT1-2
V_OUT2
V_OUT3
I_Oleak
UH, VH, and WH at the low level, I_O = 400 µA
UH, VH, and WH at the low level, I_O = 10 mA
UH, VH, and WH at the High level, I_O = –20 mA
UL, VL, and WH at the low level, I_O = 20 mA
V_CC – 1.1
0.2
0.9
V_CC – 0.9
0.3
0.5
V
1.2
V
V
V
10 µA
IHB (HA)
VICM1
VICM2
When a Hall effect device is used
Single-sided input bias mode (when a Hall IC
is used)
–2
–0.5
µA
0.5
V_CC – 2.0
V
0
V_CC
V
Hall Input Sensitivity
Hysteresis
Input voltage low → high
Input voltage high → low
CTL Amplifier
Input offset voltage
Input bias current
Common-mode input voltage range
High-level output voltage
Low-level output voltage
Open-loop gain
PWM Oscillator (PWM pin)
High-level output voltage
Low-level output voltage
External capacitor charge current
Oscillator frequency
Amplitude
∆VIN (HA)
VSLH (HA)
VSHL (HA)
V_IO (CTL)
I_B (CTL)
VICM
V_OH (CTL)
V_OL (CTL)
G (CTL)
ITOC = –0.2 mA
ITOC = 0.2 mA
f (CTL) = 1 kHz
V_OH (PWM)
V_OL (PWM)
ICHG
f (PWM)
V (PWM)
VPWM = 2.1 V
C = 2000 pF
80
15
24
5
12
–20
–12
mVp-p
40 mV
20 mV
–5 mV
–10
10 mV
–1
1 µA
0
VREG – 1.7
V
VREG – 1.2 VREG – 0.8
V
0.8
1.05
V
45
51
dB
2.75
3.0
3.25
V
1.2
1.35
1.5
V
–120
–90
–65 µA
22
kHz
1.4
1.6
1.9 Vp-p
Note:*Design target value. These items are not tested.
Continued on next page.
No.8412-2/14