|
LC72358N Datasheet, PDF (1/13 Pages) Sanyo Semicon Device – Single-Chip PLL Microcontrollers | |||
|
Ordering number : EN5065A
CMOS LSI
LC72358N, 72362N, 72366
Single-Chip PLL Microcontrollers
Overview
The LC72358N, LC72362N, and LC72366 are 1.33 µs
instruction execution time single-chip microcontrollers for
electronic tuning applications. These products incorporate
a high-speed locking circuit and a high-performance direct
PLL circuit that can control the local oscillator C/N
characteristics. These products have 256 or 512 bytes of
RAM and 16K, 24K or 32K bytes of program ROM on
chip, and incorporate a three-channel serial I/O interface,
a six-channel A/D converter and other interfaces.
Features
⢠ROM
â LC72358N: 8K steps (8191 Ã 16 bits)
â LC72362N: 12K steps (12287 Ã 16 bits)
â LC72366: 16K steps (16383 Ã 16 bits)
The subroutine area in both products is 4K steps
(4095 Ã 16 bits).
⢠RAM
â LC72358N, 72362N: 512 Ã 4 bits (banks 0 to 7)
â LC72366: 1K Ã 4 bits (banks 0 to F)
⢠Stack: Eight levels
⢠Serial I/O: Three channels (8-bit 3-wire format)
There are three internal serial clocks: 12.5 kHz,
37.5 kHz and 187.5 kHz.
⢠External interrupts:
Two channels (the INT0 and INT1 pins)
Switching between rising and falling edge detection is
supported.
⢠Internal interrupts:
Three channels
â Two internal timer interrupt channels
The timers provide eight interrupt periods: 100 µs,
1 ms, 2 ms, 5 ms, 10 ms, 50 ms, 125 ms and 250 ms.
â One serial I/O interrupt channel
⢠Multiple interrupt levels:
Four levels
Hardware priority order
INT0 pin > INT1 pin > SI/O pin > internal timer 0 >
internal timer 1
⢠A/D converter: Six channels (6-bit successive approx-
imation type)
⢠General-purpose ports
â Input ports: 10
â Output ports: 28
â I/O ports: 25 (These pins can be switched between
input and output in bit units.)
⢠PLL block
â Built-in sub-charge pump for high-speed locking
â Support for dead zone control
â Built-in unlock detection circuit
â Twelve reference frequencies: 1, 3, 3.125, 5, 6.25, 9,
10, 12.5, 25, 30, 50 and 100 kHz
⢠Universal counter: 20 bits
Supports frequency and period
measurement with counting periods
of 1, 4, 8 and 32 ms.
⢠Timers: Timer interrupt periods
100 µs, 1 ms, 2 ms, 5 ms, 10 ms, 50 ms, 125 ms
and 250 ms
⢠Beep: Six frequencies: 2.08 kHz, 2.25 kHz, 2.5 kHz,
3.0 kHz, 3.75 kHz, 4.17 kHz.
⢠Reset: Built-in voltage detection type reset circuit
⢠Cycle time: 1.33 µs (all instructions execute in one
cycle)
⢠Halt mode: The microcontroller operating clock is
stopped in halt mode.
There are four types of event that clear halt
mode: interrupt requests, timer FF
overflows, key inputs, and hold pin inputs.
⢠Operating supply voltage: 4.5 to 5.5 V (3.5 to 5.5 V
when only the controller
block operates)
⢠Package: QFP80E (QIP80E)
⢠OTP version: LC72P366
⢠Development tools: Emulator .................RE32N
Evaluation chip.......LC72EV350
Evaluation chip board
................................EB-72EV350
This LSI can easily use CCB that is SANYOâs original bus format.
⢠CCB is a trademark of SANYO ELECTRIC CO., LTD.
⢠CCB is SANYOâs original bus format and all the bus
addresses are controlled by SANYO.
SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN
63096HA (OT)/62295TH (OT) No. 5065-1/13
|
▷ |