K4S64323LF-S Datasheet, PDF (8/8 Pages) Samsung semiconductor – 2Mx32 Mobile SDRAM 90FBGA

K4S64323LF-S(D)G/S
CMOS SDRAM
SIMPLIFIED TRUTH TABLE(V=Valid, X=Don′t Care, H=Logic High, L=Logic Low)
Register
Refresh
COMMAND
Mode Register Set
Auto Refresh
Self
Refresh
Entry
Exit
Bank Active & Row Addr.
CKEn-1 CKEn CS RAS CAS WE DQM BA0,1 A10 /AP A9 ~ A 0 Note
H
X
LL
L
L
X
OP CODE
1, 2
H
3
H
LL
L
H
X
X
L
3
LH
H
H
3
L
H
X
X
HX
XX
3
H
X
LL
HHX
V
Row Address
Read &
Auto Precharge Disable
Column Address _{Auto Precharge Enable}
H
Write &
Auto Precharge Disable
Column Address _{Auto Precharge Enable}
H
X
LH
L
H
X
V
X
LH
L
L
X
V
L
Column
4
Address
H
(A0~ A7)
4, 5
L
Column
4
Address
H
(A0~ A7)
4, 5
Burst Stop
Precharge
Bank Selection
All Banks
H
X
LH
H
L
X
X
6
V
L
H
X
LL
H
L
X
X
X
H
HX
XX
Clock Suspend or
Active Power Down
Entry
H
L
X
LV
VV
X
Exit
L
H
XX
XX
X
HX
XX
Entry
H
L
X
LH
H
H
Precharge Power Down Mode
X
HX
XX
Exit
L
H
X
LV
VV
DQM
H
X
V
X
7
No Operation Command
HX
XX
H
X
X
X
LH
H
H
Notes :
1. OP Code : Operand Code
A0 ~ A 10 & BA0 ~ BA1 : Program keys. (@MRS)
2. MRS can be issued only at all banks precharge state.
A new command can be issued after 2 CLK cycles of MRS.
3. Auto refresh functions are the same as CBR refresh of DRAM.
The automatical precharge without row precharge command is meant by "Auto".
Auto/self refresh can be issued only at all banks precharge state.
4. BA0 ~ BA1 : Bank select addresses.
If both BA0 and BA1 are "Low" at read, write, row active and precharge, bank A is selected.
If BA0 is "Low" and BA1 is "High" at read, write, row active and precharge, bank B is selected.
If BA0 is "High" and BA1 is "Low" at read, write, row active and precharge, bank C is selected.
If both BA0 and BA1 are "High" at read, write, row active and precharge, bank D is selected.
If A10/AP is "High" at row precharge, BA0 and BA1 are ignored and all banks are selected.
5. During burst read or write with auto precharge, new read/write command can not be issued.
Another bank read/write command can be issued after the end of burst.
New row active of the associated bank can be issued at tRP after the end of burst.
6. Burst stop command is valid at every burst length.
7. DQM sampled at the positive going edge of CLK masks the data-in at that same CLK in write operation (Write DQM latency
is 0), but in read operation it makes the data-out Hi-Z state after 2 CLK cycles. (Read DQM latency is 2).
Rev. 1.5 Dec 2002