BU7485G-TR Datasheet, PDF (3/43 Pages) Rohm – Ground Sense High Speed Low Voltage CMOS Operational Amplifiers

BU7485G BU7485SG BU7486xxx BU7486Sxxx BU7487xx BU7487Sxx ^Datasheet
Ordering Information
B U 7 4 8 x x x x x - xx
Part Number
BU7485G
BU7485SG
BU7486xxx
BU7486Sxxx
BU7487xx
BU7487Sxx
Line-up
Topr
-40°C to +85°C
-40°C to +105°C
Package
G:FVMIISSOP5
F:FVMESOP8
SOP14
FV:FMVSSOP-B8
SSOP-B14
FVM:FFMSOP8
Packaging and forming specification
E2: Embossed tape and reel
(SOP8/SSOP-B8/SOP14/ SSOP-B14)
TR: Embossed tape and reel
(SSOP5/MSOP8)
SSOP5
SOP8
SSOP-B8
MSOP8
SOP14
SSOP-B14
SSOP5
SOP8
SSOP-B8
MSOP8
SOP14
SSOP-B14
Package
Reel of 3000
Reel of 2500
Reel of 2500
Reel of 3000
Reel of 2500
Reel of 2500
Reel of 3000
Reel of 2500
Reel of 2500
Reel of 3000
Reel of 2500
Reel of 2500
Operable Part Number
BU7485G-TR
BU7486F-E2
BU7486FV-E2
BU7486FVM-TR
BU7487F-E2
BU7487FV-E2
BU7485SG-TR
BU7486SF-E2
BU7486SFV-E2
BU7486SFVM-TR
BU7487SF-E2
BU7487SFV-E2
Absolute Maximum Ratings(Ta=25C)
Parameter
Supply Voltage
Power dissipation
Differential Input Voltage ^*8
Input Common-mode
Voltage Range
Input Current ^*9
Symbol
VDD-VSS
SSOP5
SOP8
SSOP-B8
Pd
MSOP8
SOP14
SSOP-B14
Vid
Vicm
Ii
Ratings
BU7485G/BU7486xxx
/BU7487xx
BU7485Sx/BU7486Sxxx
/BU7487Sxx
+7
0.54^*1*7
0.55^*2*7
0.50^*3*7
0.47^*4*7
0.70^*5*7
0.45^*6*7
VDD – VSS
(VSS - 0.3) to VDD + 0.3
±10
Operating Supply Voltage
Vopr
+3.0 to +5.5
Operating Temperature
Topr
-40 to +85
-40 to +105
Storage Temperature
Tstg
-55 to +125
Maximum Junction Temperature
Tjmax
+125
Note: Absolute maximum rating item indicates the condition which must not be exceeded.
Application of voltage in excess of absolute maximum rating or use out absolute maximum rated
temperature environment may cause deterioration of characteristics.
*1 To use at temperature above Ta＝25C reduce 5.4mW.
*2 To use at temperature above Ta＝25C reduce 5.5mW.
*3 To use at temperature above Ta＝25C reduce 5.0mW.
*4 To use at temperature above Ta＝25C reduce 4.7mW.
*5 To use at temperature above Ta＝25C reduce 7.0mW.
*6 To use at temperature above Ta＝25C reduce 4.5mW.
*7 Mounted on a FR4 glass epoxy PCB(70mm×70mm×1.6mm).
*8 The voltage difference between inverting input and non-inverting input is the differential input voltage.
Then input pin voltage is set to more than VSS.
*9 An excessive input current will flow when input voltages of more than VDD+0.6V or lesser than VSS-0.6V are applied.
The input current can be set to less than the rated current by adding a limiting resistor.
Unit
V
W
V
V
mA
V
C
C
C
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111ï½¥15ï½¥001
3/39
TSZ02201-0RAR1G200380-1-2
12.JUL.2013 Rev.001