|
BU9880GUL-W_12 Datasheet, PDF (18/26 Pages) Rohm – WLCSP EEPROM | |||
|
◁ |
BU9880GUL-W (64Kbit)
Datasheet
âCautions on microcontroller connection
âRs
In I2C BUS, it is recommended that SDA port is of open drain input/output. However, when to use CMOS input / output of
tri state to SDA port, insert a series resistance Rs between the pull up resistance Rpu and the SDA terminal of EEPROM.
This is controls over current that occurs when PMOS of the microcontroller and NMOS of EEPROM are turned ON
simultaneously. Rs also plays the role of protection of SDA terminal against surge. Therefore, even when SDA port is
open drain input/output, Rs can be used.
ACK
SCL
RS
SDA
'H' output of microcontroller
'L' output of EEPROM
Microcontroller
EEPROM
Figure 41. I/O circuit diagram
Over current flows to SDA line by 'H'
output of microcontroller and 'L' output
of EEPROM.
Figure 42. Input/output collision timing
âMaximum value of Rs
The maximum value of Rs is determined by following relations.
(1) SDA rise time to be determined by the capacity (CBUS) of bus line of Rpu and SDA shoulder be tR or below.
And AC timing should be satisfied even when SDA rise time is late.
(2) The bus electric potential âA to be determined by Rpu and Rs the moment when EEPROM outputs 'L' to SDA bus
should sufficiently secure the input 'L' level (VIL) of microcontroller including recommended noise margin 0.1Vcc.
A
RS
IOL
VCC
RPU=10ï½Î©
VOL
(VCCï¼VOL)ÃRS
RPU+RS
+ VOL+0.1VCCâ¦VIL
â´
RS
â¦
VILï¼VOLï¼0.1VCC
1.1VCCï¼VIL
à RPU
Example) When VCC=3V, VIL=0.3VCC, VOL=0.4V, RPU=10kâ¦,
Bus line
VIL
capacity CBUS
Microcontroller
EEPROM
Figure 43. I/O circuit diagram
from(2),
RS
⦠0.3Ã3ï¼0.4ï¼0.1Ã3
1.1Ã3ï¼0.3Ã3
⦠0.835ï¼»kâ¦ï¼½
à 10Ã103
âMaximum value of Rs
The minimum value of Rs is determined by over current at bus collision. When over current flows, noises in power source
line, and instantaneous power failure of power source may occur. When allowable over current is defined as I, the
following relation must be satisfied. Determine the allowable current in consideration of impedance of power source line
in set and so forth. Set the over current to EEPROM 10mA or below.
RPU=10Ω
'L' output
RS
'H' output
Over currentâ
Microcontroller
EEPROM
Figure 44. I/O circuit diagram
VCC
RS
â¦
I
â´ RS â§
VCC
I
Exampleï¼When VCC=3V,I=10mA
RS â§
3
10Ã10-3
⧠300[Ω]
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111ã»15ã»001
18/22
TSZ02201-0R2R0G100340-1-2
21.AUG.2012 Rev.001
|
▷ |