BU9847GUL-W_12 Datasheet, PDF (12/28 Pages) Rohm – WLCSP EEPROM

BU9847GUL-W (4Kbit)
Datasheet
●I²C BUS communication
○I²C BUS data communication
I²C BUS data communication starts by start condition input, and ends by stop condition input. Data is always 8bit long,
and acknowledge is always required after each byte.
I²C BUS carries out data transmission with plural devices connected by 2 communication lines of serial data (SDA) and
serial clock (SCL).
Among devices, there are “master” that generates clock and control communication start and end, and “slave” that is
controlled by addresses peculiar to devices.
EEPROM becomes “slave”. And the device that outputs data to bys during data communication is called “transmitter”,
and the device that receives data is called “receiver “.
SDA
1-7
8
9
1-7
8
9
1-7
8
SCL
S
START ADDRESS
condition
R/W ACK
DATA
ACK
DATA
Figure 30. Data transfer timing
9
P
ACK STOP
condition
○Start condition (start bit recognition)
・Before executing each command, start condition (start bit) where SDA goes from “HIGH” down to “LOW” when SCL is
“HIGH” is necessary.
・This IC always detects whether SDA and SCL are in start condition (start bit) of not, therefore, unless this condition is
satisfied, any command is executed.
○Stop condition (stop bit recognition)
・Each command can be ended by SDA rising from “LOW” to “HIGH” when stop condition (stop bit), namely, SCL is
“HIGH”.
○Acknowledge (ACK) signal
・This acknowledge (ACK) signal is a software rule to show whether data transfer has been made normally or not. In
master and slave, the device (μ-COM at slave address input of write command, read command, and this IC at data
output of read command) at the transmitter (sending) side releases the bus after output of 8bit data.
・This device (this IC at slave address input of write command , read command , and μ-COM at data output of read
command) at the receiver (receiving) side sets SDA “LOW” during 9 clock cycles, and outputs acknowledge signal
(ACK signal) showing that it has received the 8bit data.
・This IC, after recognizing start condition and slave address (8bit), outputs acknowledge signal (ACK signal) “LOW”.
・Each write action outputs acknowledge signal (ACK signal) “LOW”, at receiving 8bit data (word address and write data).
・Each read action outputs 8bit data (read data), and detects acknowledge signal (ACK signal) “LOW”.
・When acknowledge signal (ACK signal) is detected, and stop condition is not sent from the master (μ-COM) side, this IC
continues data output. When acknowledge signal (ACK signal) is not detected, this IC stops data transfer, and
recognizes stop condition (stop bit), and ends read action.
And this IC gets in standby status.
○Device addressing
・Output slave address after start condition from master.
・The significant 4 bits of slave address are used for recognizing a device type.
The device code of this IC is fixed to “1010”.
・Next slave addressed (A2 --- device address) are for selecting devices, and plural ones can be used on a same bus
according to the number of device addresses.
・The most insignificant bit ( R / W --- READ / WRITE ) of slave address is used for designating write or read action, and is
as shown below.
Setting R / W to 0 --- write (setting 0 to word address setting of random read)
Setting R / W to 1 --- read
Type
BU9847GUL-W
Slave address
Maximum number
of connected buses
1 0 1 0 A2 0 PS R / W
2
B _{SDA GND A2}
A
SCL WP
Vcc
PS is page select bits.
1
2
3
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
12/24
TSZ02201-0R2R0G100480-1-2
4.SEP.2012 Rev.001