R2043K Datasheet, PDF (17/48 Pages) RICOH electronics devices division – 4-wire Serial Interface

R2043K/T
Calendar Counter (Address 4-6h)
Day-of-month Counter (Address 4h)
D7
D6
D5
D4
-
-
D20
D10
0
0
D20
D10
0
0
Indefinite Indefinite
D3
D8
D8
Indefinite
D2
D4
D4
Indefinite
D1
D2
D2
Indefinite
D0
D1
D1
Indefinite
(For Writing)
(For Reading)
Default Settings *)
Month Counter + Century Bit (Address 5h)
D7
D6
D5
D4
/19⋅20 -
-
MO10
/19⋅20 0
0
MO10
Indefinite
0
0
Indefinite
D3
MO8
MO8
Indefinite
D2
MO4
MO4
Indefinite
D1
MO2
MO2
Indefinite
D0
MO1
MO1
Indefinite
(For Writing)
(For Reading)
Default Settings *)
Year Counter (Address 6h)
D7
D6
D5
D4
D3
D2
D1
D0
Y80
Y40
Y20
Y10
Y8
Y4
Y2
Y1
(For Writing)
Y80
Y40
Y20
Y10
Y8
Y4
Y2
Y1
(For Reading)
Indefinite Indefinite Indefinite Indefinite Indefinite Indefinite Indefinite Indefinite
Default Settings *)
*) Default settings: Default value means read / written values when the PON bit is set to “1” due to VDD
power-on from 0v.
*
The calendar counters are configured to display the calendar digits in BCD format by using the
automatic calendar function as follows:
The day-of-month digits (D20 to D1) range from 1 to 31 for January, March, May, July, August,
October, and December; from 1 to 30 for April, June, September, and November; from 1 to 29 for
February in leap years; from 1 to 28 for February in ordinary years. The day-of-month digits are
carried to the month digits in reversion from the last day of the month to 1. The month digits (MO10
to MO1) range from 1 to 12 and are carried to the year digits in reversion from 12 to 1.
The year digits (Y80 to Y1) range from 00 to 99 (00, 04, 08, …, 92, and 96 in leap years) and are
carried to the /19⋅20 digits in reversion from 99 to 00.
The /19⋅20 digits cycle between 0 and 1 in reversion from 99 to 00 in the year digits.
*
Any carry from lower digits with the writing of non-existent calendar data may cause the calendar
counters to malfunction. Therefore, such incorrect writing should be replaced with the writing of
existent calendar data.
Oscillation Adjustment Register (Address 7h)
D7
D6
D5
D4
D3
D2
D1
D0
DEV
F6
F5
F4
F3
F2
F1
F0
(For Writing)
DEV
F6
F5
F4
F3
F2
F1
F0
(For Reading)
0
0
0
0
0
0
0
0
Default Settings *)
*) Default settings: Default value means read / written values when the PON bit is set to “1” due to VDD
power-on from 0v.
DEV bit
When DEV is set to 0, the Oscillation Adjustment Circuit operates 00, 20, 40 seconds.
When DEV is set to 1, the Oscillation Adjustment Circuit operates 00 seconds.
F6 to F0 bits
The Oscillation Adjustment Circuit is configured to change time counts of 1 second on the basis of the
settings of the Oscillation Adjustment Register at the timing set by DEV.
Rev.2.05
12345
- 17 -