RFSA3013 Datasheet, PDF (2/17 Pages) RF Micro Devices – 75 VOLTAGE CONTROLLED ATTENUATOR

RFSA3013
Absolute Maximum Ratings
Parameter
Supply Voltage (V_DD)
Control Voltage(V_C)
Mode Pin Voltage (MODE)
RF Input Power
Operating Temperature (T_CASE)
Storage Temperature
Junction Temperature (T_J)
ESD Rating – Human Body Model (HBM)
Rating
-0.5 to +6
-0.5 to +6
-0.5 to +6
+30
-40 to +85
-65 to +150
+125
1000
Unit
V
V
V
dBm
°C
°C
°C
V
Caution! ESD sensitive device.
Exceeding any one or a combination of the Absolute Maximum Rating conditions may
cause permanent damage to the device. Extended application of Absolute Maximum
Rating conditions to the device may reduce device reliability. Specified typical perfor-
mance or functional operation of the device under Absolute Maximum Rating condi-
tions is not implied.
The information in this publication is believed to be accurate and reliable. However, no
responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any
infringement of patents, or other rights of third parties, resulting from its use. No
license is granted by implication or otherwise under any patent or patent rights of
RFMD. RFMD reserves the right to change component circuitry, recommended appli-
cation circuitry and specifications at any time without prior notice.
RFMD Green: RoHS compliant per EU Directive 2002/95/EC, halogen free
per IEC 61249-2-21, < 1000ppm each of antimony trioxide in polymeric
materials and red phosphorus as a flame retardant, and <2% antimony in
solder.
Parameter
Specification
Unit
Min. Typ. Max.
Condition
General
Supply Voltage
4.75
5
5.25
V
Supply Current
1
mA
Operating Temperature
-40
85
°C
Thermal Resistance
45
°C/W RF input must be RFIN pin
RF Input Power
27
dBm RF input must be RFIN pin
RF Performance
Frequency Range
50
3000 MHz
Minimum Insertion Loss
2.5
3.5
dB
Gain Control Range
30
35
dB
Gain versus Temperature
1.5
dB Peak to peak gain variation over temperature
for fixed control voltage
Return Loss
10
dB
Relative Phase
11
Deg Insertion phase at 15dB attenuation relative
to minimum attenuation
Input 1dB Compression Point
30
dBm
Input IP3
Input IP2
Input IH2
Input IH3
Composite Performance
CSO
42
50
80
80
50
-65
dBm
dBm
dBm
dBm
dBc
P_IN + (IM3_dBC/2)
P_IN + IM2_dBC, IM2 is F1+F2
P_IN + H2_dBC, H2 is second harmonic
P_IN + (H3_dBC/2), H3 is third harmonic
V_DD = 5V, V_C = 3.5V, T = +25°C
55.25MHz to 745.25MHz, 112 Channel,
+39dBmV input Flat Tilt
CTB
-70
dBc 55.25MHz to 745.25MHz, 112 Channel,
+39dBmV input Flat Tilt
XMOD
-60
dBc 55.25MHz to 745.25MHz, 112 Channel,
+39dBmV input Flat Tilt
Control
Voltage Control Range, Positive Attenuation Slope
0.5
4.5
V 4.5V control voltage is lowest insertion loss,
MODE pin high
Voltage Control Range, Negative Attenuation Slope
0
3.3
V 0V control voltage is lowest insertion loss,
MODE pin low
Note: Typical performance at nominal conditions unless otherwise noted: Supply voltage = 5.0V, Operating temperature = 25°C, RF Frequency
1GHz
2 of 17
7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical
support, contact RFMD at ([phone] or [e-mail].
DS120419