R5F10JBCANA Datasheet, PDF (120/138 Pages) Renesas Technology Corp – Integrated USB Controller, True Low Power Platform

RL78/G1C
3. ELECTRICAL SPECIFICATIONS (G: TA = -40 to +105°C)
(3) BC option standard (Host)
(TA = −40 to +105°C, 4.75 V ≤ UVBUS ≤ 5.25 V, 3.0 V ≤ UVDD ≤ 3.6 V, 2.4 V ≤ VDD ≤ 5.5 V, VSS = 0 V)
Parameter
Symbol
Conditions
MIN.
TYP.
MAX.
UDPi output VDSELi 1000 VP20
voltage
[3:0]
1001 VP27
(UVBUS divider (i = 0, 1)
ratio)
1010 VP20
• VDOUEi = 1
1100 VP33
38
40
42
51.6
53.6
55.6
38
40
42
60
66
72
UDMi output VDSELi 1000 VM20
voltage
[3:0]
1001 VM20
(UVBUS divider (i = 0, 1)
ratio)
1010 VM27
• VDOUEi = 1
1100 VM33
38
40
42
38
40
42
51.6
53.6
55.6
60
66
72
UDPi
VDSELi
comparing
voltage ^{Note 1}
[3:0]
(i = 0, 1)
(UVBUS divider
ratio)
1000
1001
• VDOUEi = 1
1010
• CUSDETEi = 1
VHDETP_UP0 The rise of pin voltage detection voltage
VHDETP_DWN0 The fall of pin voltage detection voltage
VHDETP_UP1 The rise of pin voltage detection voltage
VHDETP_DWN1 The fall of pin voltage detection voltage
VHDETP_UP2 The rise of pin voltage detection voltage
VHDETP_DWN2 The fall of pin voltage detection voltage
56.2
60.5
56.2
29.4
45.0
29.4
UDMi
VDSELi
comparing
voltage ^{Note 1}
[3:0]
(i = 0, 1)
(UVBUS divider
ratio)
1000
1001
• VDOUEi = 1
1010
VHDETM_UP0 The rise of pin voltage detection voltage
VHDETM_DWN0 The fall of pin voltage detection voltage
VHDETM_UP1 The rise of pin voltage detection voltage
VHDETM_DWN1 The fall of pin voltage detection voltage
VHDETM_UP2 The rise of pin voltage detection voltage
56.2
56.2
60.5
29.4
29.4
• CUSDETEi = 1
VHDETM_DWN2 The fall of pin voltage detection voltage
45.0
UDPi pull-up detection
Note 2
Connect detection with
the full speed function
(pull-up resistor)
1000
1001
1010
RHDET_PULL
In full-speed mode, the power supply
voltage range of pull-up resistors
connected to the USB function
module is between 3.0 V and 3.6 V.
1.575
UDMi pull-up detection
Note 2
Connect detection with
the low-speed (pull-up
resistor)
1000
1001
1010
RHDET_PULL
In low-speed mode, the power supply
voltage range of pull-up resistors
connected to the USB function
module is between 3.0 V and 3.6 V.
1.575
UDMi sink current
1000 IHDET_SINK
25
detection ^{Note 2}
1001
Connect detection with
the BC1.2 portable
1010
device (sink resistor)
Unit
% UVBUS
% UVBUS
% UVBUS
% UVBUS
% UVBUS
% UVBUS
% UVBUS
% UVBUS
% UVBUS
% UVBUS
% UVBUS
% UVBUS
% UVBUS
% UVBUS
% UVBUS
% UVBUS
% UVBUS
% UVBUS
% UVBUS
% UVBUS
kΩ
kΩ
μA
Notes 1. If the voltage output from UDPi or UDMi (i = 0, 1) exceeds the range of the MAX and MIN values prescribed
in this specification, DPCUSDETi (bit 8) and DMCUSDETi (bit 9) of the USBBCOPTi register are set to 1.
2. If the pull-up resistance or sink current prescribed in this specification is applied to UDPi or UDMi (i = 0,
1), DPCUSDETi (bit 8) and DMCUSDETi (bit 9) of the USBBCOPTi register are set to 1.
Remark i = 0, 1
R01DS0348EJ0100 Rev.1.00
Aug 08, 2013
Page 120 of 135