|
R5F10JBCANA Datasheet, PDF (1/138 Pages) Renesas Technology Corp – Integrated USB Controller, True Low Power Platform | |||
|
Datasheet
RL78/G1C
R01DS0348EJ0100
RENESAS MCU
Rev.1.00
Aug 08, 2013
Integrated USB Controller, True Low Power Platform (as low as 112.5 µA/MHz, and 0.61 µA for RTC + LVD),
2.4 V to 5.5 V Operation, 32 Kbyte Flash, 31 DMIPS at 24 MHz, for All USB Based Applications
1. OUTLINE
<R> 1.1 Features
Ultra-Low Power Technology
⢠2.4 V to 5.5 V operation from a single supply
⢠Stop (RAM retained): 0.23 µA, (LVD enabled): 0.31 µA
⢠Halt (RTC + LVD): 0.57 µA
⢠Supports snooze
⢠Operating: 71 µA/MHz
16-bit RL78 CPU Core
⢠Delivers 31 DMIPS at maximum operating frequency
of 24 MHz
⢠Instruction Execution: 86% of instructions can be
executed in 1 to 2 clock cycles
⢠CISC Architecture (Harvard) with 3-stage pipeline
⢠Multiply Signed & Unsigned: 16 x 16 to 32-bit result in
1 clock cycle
⢠MAC: 16 x 16 to 32-bit result in 2 clock cycles
⢠16-bit barrel shifter for shift & rotate in 1 clock cycle
⢠1-wire on-chip debug function
Code Flash Memory
⢠Density: 32 KB
⢠Block size: 1 KB
⢠On-chip single voltage flash memory with protection
from block erase/writing
⢠Self-programming with secure boot swap function
and flash shield window function
Data Flash Memory
⢠Data Flash with background operation
⢠Data flash size: 2 KB
⢠Erase Cycles: 1 Million (typ.)
⢠Erase/programming voltage: 2.4 V to 5.5 V
RAM
⢠5.5 KB size options
⢠Supports operands or instructions
⢠Back-up retention in all modes
High-speed On-chip Oscillator
⢠24 MHz with +/â 1% accuracy over voltage (2.4 V to
5.5 V) and temperature (â20°C to +85°C)
⢠Pre-configured settings: 48 MHz, 24 MHz (TYP.)
Reset and Supply Management
⢠Power-on reset (POR) monitor/generator
⢠Low voltage detection (LVD) with 9 setting options
(Interrupt and/or reset function)
USB
⢠Complying with USB version 2.0, incorporating
host/function controller
⢠Corresponding to full-speed transfer (12 Mbps) and
low-speed (1.5 Mbps)
⢠Complying with Battery Charging Specification
Revision 1.2
⢠Compliant with the 2.1A/1.0A charging mode
prescribed in the Apple Inc. MFi specification in the
USB power supply component specification Note
Direct Memory Access (DMA) Controller
⢠Up to 2 fully programmable channels
⢠Transfer unit: 8- or 16-bit
Multiple Communication Interfaces
⢠Up to 2 x I2C master
⢠Up to 1 x I2C multi-master
⢠Up to 2 x CSI (7-, 8-bit)
⢠Up to 1 x UART (7-, 8-, 9-bit)
Extended-Function Timers
⢠Multi-function 16-bit timer TAU: Up to 4 channels
(remote control output available)
⢠Real-time clock (RTC): 1 channel (full calendar and
alarm function with watch correction function)
⢠12-bit interval timer: 1 channel
⢠15 kHz watchdog timer: 1 channel (window function)
Rich Analog
⢠ADC: Up to 9 channels, 8/10-bit resolution, 2.1 µs
minimum conversion time
⢠Internal voltage reference (1.45 V)
⢠On-chip temperature sensor
Safety Features (IEC or UL 60730 compliance)
⢠Flash memory CRC calculation
⢠RAM parity error check
⢠RAM write protection
⢠SFR write protection
⢠Illegal memory access detection
⢠Clock stop/frequency detection
⢠ADC self-test
⢠I/O port read back function (echo)
General Purpose I/O
⢠5 V tolerant, high-current (up to 20 mA per pin)
⢠Open-Drain, Internal Pull-up support
Operating Ambient Temperature
⢠Standard: â40°C to + 85°C
⢠Extended: â40°C to + 105°C
Package Type and Pin Count
⢠32-pin plastic HWQFN (5 x 5)
⢠32-pin plastic LQFP (7 x 7)
⢠48-pin plastic LFQFP (7 x 7)
⢠48-pin plastic HWQFN (7 x 7)
Note
To use the Apple Inc. battery charging mode, you must
join in Apple's Made for iPod/iPhone/iPad (MFi)
licensing program. Before requesting this specification
from Renesas Electronics, please join in the Apple's
MFi licensing program.
R01DS0348EJ0100 Rev.1.00
Aug 08, 2013
Page 1 of 135
|
▷ |